Circular Saw Safety Warnings - Sparky PROFESSIONAL TK 65 Originalbetriebsanleitung

power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for which
it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and the
work to be performed. Use of the power tool for op-
erations different from those intended could result in a
hazardous situation.
5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
V - Circular saw safety
warnings
Wear hearing protection during continuous
operation. Exposure to noise can cause hearing
loss.
▪ Always hold the machine with both hands. Loss of
control can cause personal injury.
Original instructions
pages_TK 65-85-2012.indd 5
Downloaded from www.Manualslib.com manuals search engine
During operation provide eye protection to
prevent eyes from exposure to flying par-
ticles. Wear goggles.
Take protective measures against in-
halation of dust. Some materials can
contain toxic ingredients.
mask and work with dust/chip extraction when
connectable.
▪ Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
▪ Do not process materials containing asbestos. Asbes-
tos is considered carcinogenic.
▪ Use of protective gloves is recommended.
WARNING: Before connecting a tool to a
power source be sure that the voltage supply is the
same as that specified on the nameplate of the tool.
▪ A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
▪ Fully unwind cable drum extensions to avoid potential
overheating.
▪ When an extension cable is required, you must en-
sure that it has the right ampere rating for your power
tool and it is in safe electrical condition.
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance or in case of mains drop-out.
▪ Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains plug
when the cable is damaged while operating. Dam-
aged cables increase the risk of electric shock.
▪ Always keep the cord away from the working area of
the power tool.
▪ Prior to operation remove all nails, screws and other
objects from the work piece. You may damage the
saw blade and the machine by cutting into a nail or
other metal. It can also present a safety hazard.
▪ Use clamps or a vice to secure your work whenever
possible.
WARNING: Check lower guard for proper
closing before each use. Do not operate the saw if
lower guard does not move freely and close instantly.
Never clamp or tie the lower guard into the open posi-
tion.
Wear a dust
5
EN
6.8.2012 . 08:40:01 .