Maintenance; Operation; Preparing The Icemaker For Long Storage - Hoshizaki KM-35A Bedienungsanleitung

II. OPERATING INSTRUCTIONS
. This icemaker is designed to produce and store edible ice.
To keep the icemaker hygienic:
* Wash your hands before removing ice. Use the Plastic
Scoop provided (accessory).
* The Storage Bin is for ice use only. Do not store anything
else in the Bin.
* Clean the Storage Bin before use (see "III. . CLEANING").
* Keep the Scoop clean. Clean it by using a neutral cleaner
and rinse thoroughly.
* Close the Door after removing ice to prevent entrance of
dirt, dust or insects into the Storage Bin.
2. The use of any electrical equipment involves the observance
of some fundamental rules. In particular:
* Instances of high humidity and moisture increase the risk
of electrical short circuits and potential electrical shocks. If
in doubt, disconnect the icemaker.
* Do not pull the power cord in order to disconnect the
icemaker from the feed network.
* This appliance is not suitable for unsupervised use by
young children or aged or infirm persons.
3. All parts are factory-adjusted. Improper adjustments may
result in failure.
4. If the unit is turned off, wait for at least 3 minutes before
r e s t a r t i n g t h e i c e m a k e r t o p r e v e n t d a m a g e t o t h e
Compressor.

1. OPERATION

The installer will normally commission the icemaker to start the
automatic icemaking process. To ensure continuous operation, make
sure that:
* The water supply tap is on,
* The icemaker is plugged into the power supply, and
* The Control Switch is in the "ICE" position (remove the Air Filter to
check).

2. PREPARING THE ICEMAKER FOR LONG STORAGE

) Move the Control Switch to the "OFF" position.
2) Unplug the icemaker or disconnect the power supply.
3) Close the water supply tap, and remove the Inlet Hose.
4) Remove all ice from the Storage Bin, and clean the Bin.
5) Disconnect the Silicone Hose to drain the water from the Water
Tank. Reconnect the Silicone Hose back in its correct position after
all of the water has drained. See Fig. 5.
Cube Guide
Water Tank
Silicone Hose
(Connect/disconnect
arrowed part)
Downloaded from www.Manualslib.com
WARNING
Storage Bin Overflow Pipe
Fig. 5
manuals search engine
III. MAINTENANCE
1. CLEANING
WARNING
. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to check and clean the
Condenser at least once a year.
3. This appliance must not be cleaned by use of a water jet.
4. Do not use any alcohol for cleaning/sanitisation of the
icemaker. It may cause cracks on the plastic parts.
5. Do not remove the Top Panel and Louver. Only a qualified
service person should remove them.
[1] Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use
a damp cloth containing a neutral cleaner to wipe off grease or dirt.
[2] Scoop and Bin Door Grip Cleaning/Sanitisation (Daily)
) Either mix 3 litres of water with  ml of 5.25% sodium hypochlorite
solution in a suitable container, or the recommended Hoshizaki
sanitiser as directed.
2) Soak the Scoop in the solution for more than 3 minutes. Rinse
thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
3) Use a neutral cleaner to wash the Bin Door Grip. Rinse thoroughly.
4) Soak a clean cloth with the sanitising solution, and wipe the Grip.
Use fresh water and a clean cloth to rinse/dry.
[3] Storage Bin Interior Cleaning/Sanitisation (Weekly)
) Open the Storage Bin Door, and remove all ice.
2) Wash the Bin liner with a neutral non-abrasive cleaner. Rinse
thoroughly.
3) Soak a clean cloth with the neutral cleaner, and wipe the Door inner
surface. Wipe off the cleaner with a clean damp cloth.
4) Either mix 3 litres of water with  ml of 5.25% sodium hypochlorite
solution in a suitable container or the recommended Hoshizaki
sanitiser as directed.
5) Soak a clean sponge or cloth with the solution, and wipe the Bin
liner and Bin Door.
6) Rinse thoroughly with fresh water and a clean cloth to wipe off the
solution. Close the Bin Door.
Note: Some solutions may cause damage to the Bin liner surfaces
or corrosion on the metal parts. Always rinse the sanitiser
unless directed otherwise by Hoshizaki guidelines.
[4] Air Filter
A plastic mesh Air Filter removes dirt or dust from the air, and keeps
the Condenser from getting clogged. As the Filter gets clogged, the
icemaker's performance will be reduced.
Remove and clean the Air Filter at least twice per month:
) Remove the Air Filter.
Note: Do not put your hand inside the machine compartment.
2) Clean the Air Filter by using a vacuum cleaner. When severely
3
ENGLISH