Replacing The Chain Sprocket; Lubrication And Cleaning; Replacing The Carbon Brushes; Environmental Protection / Disposal - Protool SSP 200 EB Originalbetriebsanleitung/Ersatzteilliste

cover [2-1] on the clamping bolt [2-7] and tighten
by rotating the fastening wheel [2-2] clockwise.
Make sure the chain is tensioned correctly before
tightening. Check the chain for correct tension!

11.7 Replacing the chain sprocket

Remove the chain and the guide bar as described
above. Using a screwdriver, strip the snap safety
ring [8-1] from the spindle [8-4], and remove the
washer [8-2] and chain sprocket [8-3]. After re-
placement, put the washer and safety ring back
on.

11.8 Lubrication and cleaning

We recommend cleaning the machine regularly.
Remove dust, cuttings, resin and other impuri-
ties. Detergents that contain solvents can harm the
painted surfaces or plastic parts. If you use such
detergents, we recommend that you fi rst test their
effect on a small hidden surface. During mainte-
nance or replacement of any part of the tool cutting
set, clean the inside of the cover by removing the
accumulated dust and cuttings, clean the guide
groove, as well as the lubrication and tension ports
of the chain's guide bar. Do not clean the rotary
suction adaptor with your fi ngers! The motor cov-
er's ventilation ports must not be blocked!

11.9 Replacing the carbon brushes

WARNING
The saw must undergo safety inspection to main-
tain its protection category, and this work must
be done at an authorised facility licensed to per-
form such work. Before servicing the tool, always
unplug the cord from the socket!
Have an authorised service facility handle replace-
ment of the brushes, power cord, etc. If the ma-
chine is dropped, it must be checked by an au-
thorised service centre to prevent any electrical
or mechanical hazard.
After approximately 200 operating hours, the
brushes must be checked. The brushes are acces-
sible after removal of the hood. The brushes must
be replaced with new ones if they become shorter
than 5 mm.
The machine is equipped with self-detaching brush-
es that come off automatically once the minimum
length is reached. Use only original-equipment
brushes!
28
Downloaded from www.Manualslib.com manuals search engine
12 Environmental
Protection / Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into house-
hold waste!
According to the European Directive 2002/96/EC
on waste electrical and electronic equipment and
its incorporation into national law, power tools that
are no longer suitable for use must be separately
collected and sent for recovery in an environmen-
tal-friendly manner.
REACh
REACh is a European Chemical Directive that came
into effect in 2007. As "downstream users" and
product manufacturers, we are aware of our duty to
provide our customers with information. We have set
up the following website to keep you updated with
all the latest news and provide you with information
on all the materials used in our existing products:
http://www.tts-protool.com/reach

13 Warranty

For our tools, we give warranty for material and
production defects in accordance with the locally
applicable legal provisions, but in any case for at
least 12 months. Within the EU member states, the
warranty period is 24 months (verifi cation through
invoice or delivery note).
Damage caused by, in particular, natural wear, over-
loading, incorrect handling, or damage caused by
the operator, or damage caused through use of the
equipment contrary that specifi ed in the Operat-
ing Instructions, or damage which was known at
the time of purchase, is not covered by the war-
ranty. Furthermore, damage caused by the use of
non-original PROTOOL accessories and consumable
material (e.g. sanding pads) is also excluded.
Complaints can only be recognised if the tool is
returned while still assembled to the supplier or an
authorised PROTOOL Customer Service workshop.
Keep the Operating Instructions, Safety Instruc-
tions, Spare Parts List and purchase receipt in a
safe place. Otherwise the respective, current war-
ranty conditions of the manufacturer shall apply.
Note
Due to continuous research and development work,
we reserve the right to make changes to the tech-
nical content of this documentation.