Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2. Heat dissipation space
When working, the refrigerator gives off heat to
surroundings. Therefore, at least 300mm of free
space should be spared at the top side, more than
100 mm on both sides, and above 50 mm at the
back side of the refrigerator.
3. Level ground
Place the refrigerator on the solid and flat ground
(floor) to keep it stable, or else, it will give rise to
vibration and noise. When the refrigerator is
placed on such flooring materials as carpet, straw
mat, polyvinyl chloride, the solid backing plates
should be applied underneath the refrigerator, so
as to prevent color change due to heat
dissipation.
Unobstructed ventilation shall be
maintained around the appliance or in an
embedded structure.
Preparations for use
1.
Standing time
After the refrigerator is properly installed and well
cleaned, do not switch it on immediately. Make
sure to energize the refrigerator after more than
1 hour of standing, so as to ensure its normal
operation.
2.
Cleaning
Confirm the accessory parts inside the
refrigerator and wipe the inside with a soft cloth.
3.
Power-on
Insert the plug into the solid socket to start the
compressor. After 1 hour, open the freezer door,
if
the
temperature
compartment drops obviously, it indicates the
refrigeration system is working normally.
4.
Storage of food
After the refrigerator runs for a period of time, the
internal temperature of the refrigerator will be
automatically controlled according to the user's
temperature setting. After the refrigerator is fully
cooled, put in foods, which usually need 2~3 hours
to be fully cooled. In summer, when the
temperature is high, it takes more than 4 hours for
the foods to be fully cooled (Try to open the
refrigerator door as less as possible before the
internal temperature cools down).
If the refrigerator is installed in the moisture
place, make sure to check whether the ground
wire and leakage circuit breaker are normal. If
vibration noises are produced due to the
refrigerator contacting the wall or if the wall gets
blackened by
air
compressor, move the refrigerator away from the
inside
the
freezer
convection around the
wall. Setting up the refrigerator may cause
jamming noise or image chaos to the mobile
phone, fixed-line telephone, radio receiver,
television set surrounding it, so try to keep the
refrigerator as far away as possible in such case.
Functions
Temperature selection
The temperature of the
appliance can be adjusted by
turning the thermostat dial.
• The thermostat can be set
between 1 and 7.
• 1 is the warmest setting.
• 7 is the coldest setting.
• The recommended setting
is 4.
• Set the dial to 0 to turn off
the cooling function.
Internal temperature of the
appliance can vary based on
ambient temperature, the
quantity of items stored and
how frequently the door is
opened.
Fast Freeze
1. Fast freezing makes water in the food form
into fine ice crystal, so as to prevent the cell
membrane from being damaged and the
cytoplasm from being lost when thawing, thus
preserving the original freshness and nutrition of
food.
2. Fresh food and fish to be preserved for a long
time should be frozen in a fast manner. To realize
fast freezing, please adjust the knob switch to
mode "7" before adding the food.
3. After fast freezing, turn the knob back to its
original mode (In general, the fast freezing time
shall not exceed 4 hours).
Instructions for food storage
Precautions for use
⚫ The appliance might not operate consistently
(there is
possibility
temperature becoming too warm in the
frozen food compartment) when sited for an
extended period of time below the cold limit
of the temperature range for which the
refrigerating appliance is designed
⚫ The information of climate type of the
appliance is provided on the rating plate.
⚫ The internal temperature could be affected
of
defrosting
or
9
Werbung
Kapitel
