Black&Decker Dustbuster DV7210EL Bersetzung Der Ursprünglichen Anweisungen Seite 6

ENGLISH
Charging the battery (Fig. D)
Place the appliance on the charging base (7)
u
Plug in the charger. Switch on at the mains. The charging
u
indicator (3) will flash continuously (slowly)
Leave the appliance to charge.
u
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indefinitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
The charge is complete when the charging indicator (3) lights
continuously. The charger and the battery can be left connect-
ed indefinitely with the LED illuminated. The LED will change
to flashing (charging) state as the charger occasionally tops
off the battery charge. The charging indicator (3) will be lit as
long as the battery is connected to the plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
Battery diagnostics
If the appliance detects a weak battery, the charging indica-
tor (3) will flash at a fast rate when the power button (1) is
activated. Proceed as follows:
Place the appliance on the charging base (7)
u
Plug in the charger. Switch on at the mains.
u
Leave the appliance to charge.
u
If the appliance detects a damaged battery, the charging
indicator (3) will flash at a fast rate when the appliance is on
the charger base. Proceed as follows:
Take the appliance and the charger to be tested at an
u
authorised services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink, fast and slow, one
flash at each speed and repeat.
Switching on and off (fig. E)
To switch the appliance on, slide the on/off switch (1)
u
forward to position 1.
To switch the appliance off, slide the on/off switch (1) back
u
to position 0.
6
Downloaded from www.Manualslib.com
(Original instructions)
manuals search engine
Rotating the dust collector (fig. F) (DV1010EL and
DV1410EL only
The nozzle can be rotated for better access in tight spots.
Press the rotation release catch (12).
u
Rotate the nozzle to the left or right until it clicks into
u
place.
Optimising the suction force
In order to keep the suction force optimised, the filters must be
cleared regularly during use.
Emptying and cleaning the product.
Emptying the dust bowl (fig. G).
Press the release latch (13) and pull the dust collector (5)
u
straight off.
Empty the contents of the bowl.
u
To replace the dust collector, place it back onto the handle
u
until it "clicks" firmly into position.
Removing the dust bowl and filters (fig. H, I, J & K).
Warning! The filters are re-usable and should be cleaned
regularly.
Press the release latch (2) and pull the dust bowl (4)
u
straight off.
While holding the dust bowl over a bin or sink, pull out the
u
filter (14) to empty the contents of the bowl.
To replace the dust bowl, place it back onto the handle
u
until it "clicks" firmly into position.
Warning! Never use the appliance without the filters. Opti-
mum dust collection will only be achieved with clean filters.
Pre-filter (fig. J) (DV7210EL and DV1010EL)
The Filter and pre-filter can be separated to allow better
cleaning.
Twist the pre-filter (16) in a clockwise direction and lift
u
from the filter (15).
Quick clean filter (fig. K) (DV1410EL)
Lift the filter cleaning handle (19).
u
Whilst holding the quick clean filter housing (17) turn the
u
filter cleaning handle (18) to perform a quick clean of the
filter (18).
Pull the filter (18) out of the quick clean filter housing (17)
u
for more thorough cleaning.
Cleaning the dust bowls and filters
The dust bowls and filters can be washed in warm soapy
u
water.
Make sure that the filters and the dust bowl are dry before
u
re-fitting.