Safety Notes - Bosch AXT Rapid 2000 Bedienungsanleitung

F 016 L70 461 - GB Seite 1 Freitag, 7. Juli 2006 1:40 13
STOP
During operation, do not reach into the feed opening 1 or the dis-
charge chute 8. The machine runs on for a few seconds after be-
ing switched off.
Before switching on, the machine must be assembled according to the
enclosed instructions.
It is recommended for increased electrical safety to use a Residual
Current Device (RCD) with a tripping current of not more than 30 mA.
Always check your RCD every time you use it.
Use only extension cables that are intended for outdoor use and are
protected against splashes of water.
Do not touch the plug or socket with wet hands.
Do not drive over, crush or stretch the cable.
Do not allow children to operate this equipment.
Other persons and animals should remain at a distance of 3 metres or
more when the machine is being used. The operator is responsible for
third persons in the working area.
Bosch can assure flawless functioning of the machine only when orig-
inal accessories are used.
Become familiar with the owner's manual before attempting to operate
this machine.
Avoid wearing loose-fitting clothing, hanging cords or ties.
Only operate the machine in open space (eg not too close to a wall or
other fixed objects) and on a firm, level surface.
Do not operate the machine on paved or gravel surface where ejected
material could cause injury.
12 • F 016 L70 461 • TMS • 07.07.06
Downloaded from www.Manualslib.com

Safety Notes

Warning: Read these instructions carefully, be familiar
with the controls and proper use of the machine.
Please keep the instructions safe for later use. Before
using for the first time, ask for a practical demonstra-
tion.
Read instruction manual.
Danger – rotating blades, keep hands and feet out of open-
ings while the machine is running.
Before handling the cutter, switch off and remove the plug
from the mains supply. If the cable is damaged or cut
through while working, do not touch the cable but immedi-
ately remove the plug from the mains supply. Never use the
machine with a damaged cable.
Do not operate this equipment in the vicinity of bystanders.
Keep bystanders a safe distance away from the machine.
Wait untill all machine components have completely
stopped before touching them.
Do not expose the machine to rain. Only store the machine
in a dry place.
Wear protective gloves, sturdy shoes and long trousers.
Obtain and wear eye and ear protection at all times while
operating the machine.
Dispose of this product in an environmetally friendly way.
manuals search engine
Before starting the machine, check that all screws, nuts, bolts and
other fasteners are properly secured and that guards and screens are
in place. Replace damaged or unreadable warning and operating la-
bels.
Before starting the machine, make certain that the feed intake is
empty.
Keep your face and body away from the feed intake opening.
Do not allow hands or any other part of the body or clothing inside the
feed intake opening, discharge chute or near any moving part.
Switch off the machine before attaching or removing the bag.
Keep proper balance and footing at all times. Do not overreach.
Never stand at a higher level than the base of the machine when feed-
ing material.
Always stand clear of the discharge zone when operating the ma-
chine.
When feeding material into the machine be extremely careful that
pieces of metal, rocks, bottles, cans or other foreign objects are not
included.
If the cutting mechanism strikes any foreign object or if the machine
should start making any unusual noise or vibration, immediately
switch off and allow the cutter to stop. Remove the plug from the
mains supply and take the following steps:
– Inspect for damage.
– Replace or repair any damaged parts.
– Check for and tighten any loose parts.
Do not attempt to repair the machine unless you are qualified to do so.
Do not allow processed material to build up in the discharge zone; this
may prevent proper discharge which can result in kickback of material
through the feed intake opening.
If the machine becomes clogged, switch off and allow the cutter to
stop. Remove the plug from the mains supply before clearing debris.
Keep all guards and deflectors in place and in good working condition.
Do not tamper with the motor speed control settings. Contact a Bosch
approved service agent if a problem exists.
Keep the motor cooling vents clean of debris and other accumulations
to prevent damage to the motor or possible fire.
Do not transport the machine while the motor is running.
Switch off, allow the cutter to stop and remove the plug from the mains
supply whenever you leave the work area.
Do not tilt the machine while it is running.
Maintenance and storage:
– When the machine is stopped for servicing, inspection, or storage,
or to change an accessory, switch off and remove the plug from
the mains supply and allow the machine to cool. Make sure that all
moving parts have come to a complete stop before making any in-
spections, adjustments, etc.
– Maintain the machine with care and keep it clean.
– Replace worn or damaged parts for safety. Ensure all replacement
parts are Bosch Approved.
– If an extension cord is used it shall not be of lighter grade than the
supply cord already fitted to the machinemachine.
– Check the supply and any extension cord regularly for damage or
signs of ageing.
Do not use the machine, if the cords are damaged.
– When servicing the cutter be aware that, even though the motor
will not start due to the interlock feature of the guard, the cutter can
still be moved if the motor is turned by hand.
– Never attempt to override the interlock feature of the guard.
English - 1