Safety Notes - Bosch AXT 25 D Originalbetriebsanleitung

OBJ_BUCH-895-003.book Page 12 Monday, April 11, 2011 1:52 PM
12 | English

Safety Notes

en
Warning: Read these instructions carefully,
be familiar with the controls and proper use
of the machine. Please keep the instructions
safe for later use. Before using for the first
time, ask for a practical demonstration.
Explanation of symbols on the machine
General hazard safety alert.
Read instruction manual.
Before handling the cutter, switch
off and remove the plug from the
mains supply. If the cable is dam-
aged or cut through while working,
do not touch the cable but immedi-
ately remove the plug from the
mains supply. Never use the ma-
chine with a damaged cable.
Wear protective gloves, sturdy shoes
and long trousers.
Danger – rotating blade. Keep
hands and feet out of openings while
the machine is running.
Pay attention that bystanders are
not injured through foreign objects
thrown from the machine.
Keep bystanders a safe distance
away from the machine.
Wait until all machine components
have completely stopped before
touching them.
STOP
Wear eye protection.
Wear ear protection.
Do not use the machine in the rain or
leave it outdoors when it is raining.
Do not stand on the collection box.
Operation
During operation, do not reach into the
chute assembly 8. The machine runs on for
a few seconds after being switched off.
Never allow children or people unfamiliar
with these instructions to use the ma-
chine. Local regulations may restrict the
age of the operator. When not in use store
the machine out of reach of children.
This tool is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a per-
son responsible for their safety.
F 016 L70 735 | (11.4.11)
Children should be supervised to ensure
that they do not play with the appliance.
Before switching on, the machine must be
assembled according to the enclosed in-
structions.
It is recommended for increased electrical
safety to use a Residual Current Device
(RCD) with a tripping current of not more
than 30 mA. Always check your RCD every
time you use it.
Use only extension cables that are intend-
ed for outdoor use and are protected
against splashes of water.
Do not touch the plug or socket with wet
hands.
Do not run over, crush or pull the power
supply cable or extension lead, otherwise
it may be damaged. Protect the cable from
heat, oil and sharp edges.
Other persons and animals should remain
at a distance of 3 metres or more when the
machine is being used. The operator is re-
sponsible for third persons in the working
area.
Bosch can assure flawless functioning of
the machine only when original accesso-
ries are used.
Become familiar with the instruction man-
ual before attempting to operate this ma-
chine.
Avoid wearing loose-fitting clothing, hang-
ing cords or ties.
Only operate the machine in open space
(e. g. not too close to a wall or other fixed
objects) and on a firm, level surface.
Do not operate the machine on paved or
gravel surface where ejected material
could cause injury.
Before starting the machine, check that all
screws, nuts, bolts and other fasteners are
properly secured and that guards and
screens are in place. Replace damaged or
unreadable warning and operating labels.
Before starting the machine, make certain
that the chute assembly is empty.
Keep your face and body away from the
chute assembly.
Do not allow hands or any other part of the
body or clothing inside the chute assembly,
discharge chute or near any moving part.
Keep proper balance and footing at all
times. Do not overreach. Never stand at a
higher level than the base of the machine
when feeding material.
Always stand clear of the discharge zone
when operating the machine.
When feeding material into the machine be
extremely careful that pieces of metal,
rocks, bottles, cans or other foreign ob-
jects are not included.
If the cutting mechanism strikes any for-
eign object or if the machine should start
making any unusual noise or vibration, im-
mediately switch off and allow the cutter
to stop. Remove the plug from the mains
supply and take the following steps:
– Inspect for damage.
– Replace or repair any damaged parts.
– Check for and tighten any loose parts.
Bosch Power Tools