Other Functions - Purmo YALI DIGITAL Installations- Und Bedienungs-Anleitung

GB
GENERAL
INFORMATION
NOTE: Radiators must be connected as masters in this case.
Each and every radiator must also be defined as master in
the parameter menu.
NOTE: Do not connect an external thermostat directly to pin
1 or 2 as this will shorten the life of the radiator.
OTHER FUNCTIONS
TIMER FUNCTION
The timer function allows you to override the
programmed settings (temperature and operating mode)
for a chosen period of time, starting from the moment
that the timer function is activated.
• Move the frame cursor to the timer icon.
• Confirm your choice with the "OK" key.
• Set the desired temperature using the"+" and "-" keys
and confirm with the "OK" key.
• Adjust the period using the "+" and "-" keys between
1 hour and 44 days. Confirm with the "OK" key.
• The icon will start to blink and the desired
temperature and hand
end of the set period.
• If you want to stop the timer before the end of the set
period, select another mode using the left "" or right
"" navigation key and confirm with the "OK" key.
FRONT PANEL TEMPERATURE LIMITATION
This power setting can be used to limit the output of the
heating element in the front panel and as a consequence
will limit the surface temperature of the front panel.
• Move the frame cursor to the power icon
• Confirm your choice with the "OK" key.
• Use the "+" and "–" keys to change the output of the
front panel from 100% (Index 3 in section 2 of the LCD -
Factory setting) to 70% (Index 2 in section 2 of the LCD)
or 55% (Index 1 in section 2 of the LCD) (corresponding
to a maximum surface temperature of 90, 75 or 60°C)
and confirm with the "OK" key.
• The thermostat will return to the "Comfort" mode.
• The display will then show in the right upper corner
(section 2 of the LCD) the index corresponding to the
maximum surface temperature of the front panel.
NOTE: If the radiator is connected to a Touch E3, this
setting must be made on the Touch E3, or it will be
overwritten by the Touch E3.
94
icon are displayed until the
.
NOTE: When considering the permanent use of the
radiator at 60°C or 75°C maximum, the following
correction factor should be applied for the output.
INDEX IN SURFACE
SECTION 2 TEMPERATURE
1 ~ 60°C max
2 ~ 75°C max
3 ~ 90°C max
E.g. A 1000 Watt single panel programmed for a
maximum surface temperature of 75°C will deliver
maximum 700 Watts. A 1000 Watt double panel
programmed for a maximum surface temperature of
60°C will deliver maximum 800 Watts. These values
should be considered when selecting the number and
type of panels to cover the calculated heat losses.
KEY LOCK FUNCTION
Use the Key Lock function to prevent any changes to
your settings (in a child's room, public area... etc)
• To activate the Key Lock function, first press and
maintain the "OK" key and then simultaneously on
the left "" and right "" navigation keys.
• The key icon, in section 4 of the LCD display, will be
displayed on the screen.
• Repeat the same procedure to unlock the keypad.
This function is available in all operating modes.
BEHAVIOUR INDICATOR
This is the bar at the bottom of the LCD display that
gives a visual indication of how much energy the
current temperature setting is using i.e.
red = high
orange = medium
green = low energy comsumption
As you increase the temperature setting, the behavior
indicator "bar" in section 8 of the LCD display, will increase
in length. The opposite applies when decreasing the
temperature setting.
NOTE: The behaviour indicator is replaced by the program
information bar when in Automatic mode.
SINGLE DOUBLE
PANEL PANEL
~ 0.55 ~ 0.80
~ 0.70 ~ 0.90
1 1