Spark Plug; Preparation For Storage; Preparation For Transport; Service Information - Parkside PHDB 4 C3 Bedienungs- Und Sicherheitshinweise

See technical specifications for oil type and fill
quantity.
ATTENTION
• To check the oil level, do not screw in the oil tank cover
with oil dipstick (43), but only insert it up to the thread.
14.2.2 Automatic oil switch-off
The automatic oil switch-off activates if there is too little engine
oil and switches the engine off. If this happens, the engine can-
not be restarted or switches off again after a short while. A
restart is only possible after the oil has been topped up (see
chapters 10.1 and 14.2.1 before each use).
14.2.3 Air filter (Fig. 1)
Clean the air filter (9) regularly, replace if necessary.
• Remove the air filter cover (9). Pull carefully on the edges of
the air filter (9).
• Remove the contaminated filter element.
• Knock out the contaminated filter element or blow it out with
compressed air at low pressure.
• Replace the filter element and the air filter cover (9).

14.2.4 Spark plug

Check the spark plug/spark plug connector (24) for the first
time after 20 operating hours for contamination and clean if
necessary with a wire brush. Afterwards, service the spark plug
after every 50 hours of operation.
• Remove the spark plug connector (24) from the spark plug
by turning it.
• Remove the spark plug with the supplied spark plug span-
ner (36).
• Assembly is done in the reverse order.

14.2.5 Preparation for storage

Note:
Petrol must be disposed of in an environmentally friendly
manner!
• Empty the fuel tank (15) with a fuel suction pump (not in-
cluded in the scope of delivery).
• Start the engine and leave it running until the remaining pet-
rol has been used up.
• Change the oil after every season. To do this, drain the old
engine oil from the warm engine and refill with new oil.
• Remove the spark plug. Use an oil can to fill approx. 20
ml oil in the cylinder. Pull the pull starter (26) slowly so that
the oil coats the inside of the cylinder. Screw the spark plug
back in.
• Store the appliance in a well-ventilated location.

14.2.6 Preparation for transport

Note:
Petrol must be disposed of in an environmentally friendly
manner!
• Empty the fuel tank (15) with a fuel suction pump (not in-
cluded in the scope of delivery).
• If still operational, leave the engine running until the remain-
ing petrol has been used up.
• Remove the engine oil from the warm engine (as described).
• Remove the spark plug connector (24) from the spark plug.
• Secure the appliance against slipping using securing straps.

14.3 Service information

Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
Wear parts*: Spark plug, high-pressure hose, jet pipe, nozzles,
air filter
* Not necessarily included in the scope of delivery!

15. Storage

m CAUTION
Risk of injury and damage!
• Take the weight of the appliance into account when storing.
Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the device in its original packaging.
Cover the device to protect it from dust or moisture.
Store the operating manual with the device.

16. Disposal and recycling

The equipment is supplied in packaging to prevent it from be-
ing damaged in transit. The raw materials in this packaging
can be reused or recycled.
The equipment and its accessories are made of various types
of material, such as metal and plastic. Defective components
must be disposed of as special waste. Ask your dealer or your
local council.
The packaging is wholly composed of environment-
ally-friendly materials that can be disposed of at a
local recycling centre.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
electrical devices.
GB/IE 31