Technical Data - AEG POWERTOOLS PM 10 E Originalbetriebsanleitung

TECHNICAL DATA

Rated input ...........................................................................................
Output ...................................................................................................
No-load speed ......................................................................................
Speed under load .................................................................................
Rate of percussion under load..............................................................
Single impact strength ..........................................................................
Drilling capacity in concrete ..................................................................
Tunnel bit in concrete, bricks and limestone ........................................
Core cutter in concrete, bricks and limestone ......................................
Weight without cable ............................................................................
E
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ....................................................
Sound power level (K = 3 dB(A)) ........................................................
Wear ear protectors!
E
Typically the A-weighted sound pressure level of the
tool is ....................................................................................................
Measured values determined according to 2000/14/EG at the user's ear.
2000/14/EC: Conformity assessment procedure according to Annex
63069 Offenbach, Germany
Measured sound power level ............................................................
Guaranteed sound power level .........................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a :
h
Hammer-drilling in concrete..................................................................
Uncertainty K = ....................................................................................
Chiselling ..............................................................................................
Uncertainty K = ....................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
and/or serious injury.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Loss of control can
cause personal injury.
Cutting accessory
contacting a live wire may make exposed metal parts of the power
tool live and shock the operator.
Appliances used at many different locations including open air
should be connected via a residual current device of 30 mA or less.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched off.
20 ENGLISH
Downloaded from www.Manualslib.com
PN 11 E
........................... 1700 W .............................. 1600 W
............................. 850 W ................................ 800 W
-1
......................125-250 min .................................-
......................125-250 min -1 .................................-
....................975-1950 min -1 ...................975-1950 min
............................7-27 J ................................7-27 J
..........................28-50 mm ..................................-
..........................50-80 mm ..................................-
........................45-150 mm ..................................-
............................ 11,8 kg .............................. 11,0 kg
............................. 100 dB (A)
..............................111 dB (A)
................................... ..................................... 91 dB (A)
................................... ................................... 102 dB (A)
................................... ................................... 105 dB (A)
2
............................ 12,5 m/s
................................. 2 m/s 2
............................... 11 m/s 2 .............................. 11 m/s
2
................................. 2 m/s ................................ 2 m/s
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
. Failure to
cables and gas or waterpipes.
Under the effect of extreme electromagnetic interferences from the
outside, tempo-rary variations in the speed of rotation could arise in
particular cases.
The dust that arises when working with this tool can be detrimental
to health and therefore not reach the body. Wear a suitable dust
protection mask.
SPECIFIED CONDITIONS OF USE
PN 11 E: The pneumatic hammer can be universally used for
hammer drilling and chiselling in stone and concrete.
PM 10 E: The hammer can be used for chiselling and demolition.
Do not use this product in any other way as stated for normal use.
manuals search engine
PM 10 E EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized documents.
EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3,
in accordance with the regulations 98/37/EC, 2004/108/EC,
-1 2000/14/EC (PM 10 E).
Winnenden, 2009-01-25
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to safety
class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Important note! If the carbon brushes are worn, in addition to
exchanging the brushes the tool should be sent to after-sales
service. This will ensure long service life and top performance.
Use only AEG accessories and spare parts. Should components
need to be exchanged which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at: AEG
2
Elektrowerkzeuge, Max-Eyth-Straße 10, D-71364 Winnenden,
2
Germany.
SYMBOLS
Please read the instructions carefully before starting
the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of European
Directive 2002/96/EC on waste electrical and
electronic equipment and its implementation in
accordance with national law, electric tools that have
reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Rainer Kumpf
Manager Product Development
ENGLISH 21