Inhaltsverzeichnis
Werbung
This monitor is specially tested for use in pregnancy and
pre-eclampsia. When you detect unusual high readings in
pregnancy, you should measure after a short while again
(eg. 1 hour). If the reading is still too high, consult your
doctor or gynecologist.
How do I evaluate my blood pressure?
Table for classifying home blood pressure values in adults in
accordance with the international Guidelines (ESH, ESC, JSH).
Data in mmHg.
Range
Systolic
1. blood pressure
< 120
normal
2. blood pressure
120 - 129 74 - 79
optimum
3. blood pressure
130 - 134 80 - 84
elevated
4. blood pressure too
135 - 159 85 - 99
high
5. blood pressure
≥ 160
dangerously high
The higher value is the one that determines the evaluation.
Example: a blood pressure value of 140/80 mmHg or a value of
130/90 mmHg indicates «blood pressure too high».
2. Using the Device for the First Time
Inserting the batteries
After you have unpacked your device, first insert the batteries. The
battery compartment 4 is on the bottom of the device. Insert the
batteries (4 x 1.5 V, size AA), thereby observing the indicated
polarity.
Setting the date and time
1. After the new batteries are fitted, the year number flashes in the
display. You can set the year by pressing the M-button AK. To
confirm and then set the month, press the time button AL.
2. Press the M-button to set the month. Press the time button to
confirm and then set the day.
3. Follow the instructions above to set the day, hour and minutes.
4. Once you have set the minutes and pressed the time button, the
date and time are set and the time is displayed.
BP A3L Comfort
Recommenda-
Diastolic
tion
< 74
Self-check
Self-check
Self-check
Seek medical
advice
≥ 100
Urgently seek
medical advice!
5. If you want to change the date and time, press and hold the time
button down for approx. 3 seconds until the year number starts
to flash. Now you can enter the new values as described above.
Selecting the correct cuff
Microlife offers different cuff sizes. Select the cuff size to match the
circumference of your upper arms (measured by close fitting in the
centre of the upper arm).
Cuff size
for circumference of upper arm
M
22 - 32 cm
M - L
22 - 42 cm
L
32 - 42 cm
Pre-shaped cuffs are optionally available.
Only use Microlife cuffs.
Contact your local Microlife Service if the enclosed cuff 6 does
not fit.
Connect the cuff to the device by inserting the cuff connector 7
into the cuff socket 3 as far as it will go.
If you buy a spare Microlife cuff, please remove the cuff
connector 7 from the cuff tube AL from the cuff supplied
with the original device and insert this cuff connector into
the tube of the spare cuff (valid for all cuff sizes).
Selecting the user
This device allows to store the results for 2 individual users.
Before each measurement, set the user switch AT for the
intended user: user 1 or user 2.
User 1: slide the user switch AT upwards to the user 1 icon.
User 2: slide the user switch AT downwards to the user 2 icon.
The first person to measure should select user 1.
Selecting standard or MAM mode
This device enables you to select either standard (standard single
measurement) or MAM mode (automatic triple measurement). To
select standard mode, slide the MAM switch 9 on the side of the
device downwards to position «1» and to select MAM mode, slide
this switch upwards to position «3».
MAM mode (highly recommended)
In MAM mode, 3 measurements are automatically taken in
succession and the result is then automatically analysed and
displayed. Because the blood pressure constantly fluctuates, a
result determined in this way is more reliable than one produced
by a single measurement.
EN
3
Werbung
Kapitel
Inhaltsverzeichnis
