Electrical Connection; Cleaning; Transport; Storage - Scheppach HS510 Original Bedienungsanleitung

Electrical connection

The electrical motor installed is connected and ready
for operation. The connection complies with the ap-
plicable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these reg-
ulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H07RN-F".
The printing of the type designation on the connec-
tion cable is mandatory.
For single-phase AC motors, we recommend a fuse
rating of 16A (C) or 16A (K) for machines with a high
starting current (starting from 3000 watts)!

11. Cleaning

Attention!
Pull out the power plug before carrying out any clean-
ing work on the equipment.
We recommend that you clean the equipment imme-
diately after you use it.
Clean the equipment regularly with a damp cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these may be aggressive to the plastic parts in
the equipment. Ensure that no water can get into the
interior of the equipment.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

12. Transport

Place the jack in the transport position and secure it
with the locking lever (6). In order to move the saw
easily, tip it in the direction of the person moving it.

13. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.

14. Maintenance

Attention!
Pull out the power plug before carrying out any main-
tenance work on the equipment.
Connections and repairs
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Adjustment of the jack stop, (3) (Fig. 6)
Set the entry point of the jack with the adjustment
screw (6a).
Change of saw blades (Fig. 7 - 10)
1. Unplug the unit.
2. Wait until the blade stops rotating and the motor
has cooled down.
3. Bring the jack into the transport position and lock
the saw in this position with the locking lever.
4. Remove the hexagon nut (7a) from the guide (7a).
5. Now push the guide (7b) out of the threaded pin.
6. Remove the spring split pin (19) from the recoil
spring (18).
7. Loosen the locking lever and grasp the jack firmly
so that it does not fall down and the recoil spring
cannot jump out of the unit in an uncontrolled
fashion.
8. Tip the jack carefully back and place it on the
ground. (Fig. 9)
9. Use the locking bolt (10a) to lock the saw blade.
Insert it through the outer hole in the saw blade
guard (15).
10. Use the saw blade wrench (fig. 13) to open the
hexagon nut (10b) and remove it along with the
washer (10c) and the flange (10d).
11. Carefully remove the saw blade. Wear protective
gloves for this part of the work. (Attention: there is
danger of injury, so please take caution!)
12. Before replacing the saw flange, clean the flange
with a cloth or soft brush.
GB | 23