Berner BACAGXB 18V Originalbetriebsanleitung Seite 17

Maintain power tools. Check for misalign-
u
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tool's operation. If damaged, have
the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power
tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
Recharge only with the charger specified by
u
the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
Use power tools only with specifically desig-
u
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
When battery pack is not in use, keep it away
u
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or a
fire.
Under abusive conditions, liquid may be ejec-
u
ted from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical
help. Liquid ejected from the battery may
cause irritation or burns.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Safety information for the angle
grinder
English
Safety Warnings common for Grinding,
Sanding, Wire Brushing or Abrasive Cutting Off
operations
English
This power tool is intended to function as a
u
grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions, illus-
trations and specifications provided with this
power tool. Failure to follow all instructions lis-
ted below may result in electric shock, fire and/
or serious injury.
1 609 92A 5K8 • 29.6.20
English
Operations such as polishing are not recom-
u
mended to be performed with this power
tool. Operations for which the power tool was
not designed may create a hazard and cause
personal injury.
Do not use accessories which are not spe-
u
cifically designed and recommended by the
tool manufacturer. Just because the access-
ory can be attached to your power tool, it does
not assure safe operation.
The rated speed of the accessory must be at
u
least equal to the maximum speed marked on
the power tool. Accessories running faster
than their rated speed can break and fly apart.
The outside diameter and the thickness of
u
your accessory must be within the capacity
rating of your power tool. Incorrectly sized ac-
cessories cannot be adequately guarded or
controlled.
Threaded mounting of accessories must
u
match the grinder spindle thread. For ac-
cessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not
match the mounting hardware of the power tool
will run out of balance, vibrate excessively and
may cause loss of control.
Do not use a damaged accessory. Before
u
each use inspect the accessory such as ab-
rasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no load speed for
one minute. Damaged accessories will nor-
mally break apart during this test time.
Wear personal protective equipment. De-
u
pending on application, use face shield,
safety goggles or safety glasses. As appropri-
ate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments.
The eye protection must be capable of stop-
ping flying debris generated by various opera-
tions . The dust mask or respirator must be
capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity
noise may cause hearing loss.
Keep bystanders a safe distance away from
u
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken access-
ory may fly away and cause injury beyond im-
mediate area of operation.
English | 17