Technical Data; Hand-Arm Vibration - Parkside PWDS 920 A1 Originalbetriebsanleitung

a) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Al-
ways use auxiliary handle, if provided, for maximum con-
trol over kickback or torque reaction during start-up. The
operator can control torque reactions or kickback forces,
if proper precautions are taken.
b) Never place your hand near the rotating accessory. Ac-
cessory may kickback over your hand.
c) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool
in direction opposite to the wheel's movement at the point
of snagging.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners,
sharp edges or bouncing have a tendency to snag the ro-
tating accessory and cause loss of control or kickback.
Safety warnings specific for sanding operations
a) Do not use excessively oversized sanding disc
paper. Follow manufacturers recommenda-
tions, when selecting sanding paper.
Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging,
tearing of the disc or kickback.
Additional safety instructions
a) Connect a vacuum cleaner to the supplied
adapter before starting your operations.
b) Attention! Keep away sanding dust from open fire.
Dust may be explosive.
c) Always wear goggles and a dust mask when
sanding, in particular during overhead work
and when processing critical materials!
When sanding certain materials (e. g. lead paint, certain
types of wood and metal) harmful or noxious dust may be
generated. Touching or breathing in such dust may imply
risks for the operator or bystanders.
Notes regarding vibration and noise emissions
Reduce noise emissions and vibrations to a minimum!
1. Only use power tools which are free of defects.
2. Maintain and clean the power tool on a regular basis.
3. Adjust your way of working to the power tool.
4. Do not overload your power tool.
5. Have your power tool inspected, if necessary.
6. Switch off the power tool when it is not in use.
Remaining risks
Even if you use this power tool in compliance with the regula-
tions, there are still remaining risks. The following risks may oc-
cur due to the type and design of the power tool:
a) Damage caused to your health resulting from hand/arm
vibrations if the power tool is used over a Ionger period of
time or if it is not properly used and maintained.
b) Injury and damage to property caused by flying off in-
sertion tools which are unexpectedly expelled from the
power tool due to sudden damage, wear or incorrect
insertion.
c) Burns and cuts if the insertion tools are touched directly
after use and/or with your bare hands.
16 GB/IE
Warning! This electric tool generates an electromagnetic
field during operation. This field can impair active or passive
medical implants under certain conditions. In order to prevent
the risk of serious or deadly injuries, we recommend that per-
sons with medical implants consult with their physician and the
manufacturer of the medical implant prior to operating the elec-
tric tool.

6. Technical data

Mains connection
Motor rating
Operating mode
Nominal speed
(oscillation rate) n
Spindle size
Grinding disc diameter
Abrasive paper diameter
Protection class
Weight
Sound pressure Ievel L
pA
Sound power Ievel L
WA
Uncertainty K (K /K )
pA WA

Hand-arm vibration

When grinding with
abrasive sheets, DS
Uncertainty K
The specified hand-arm vibration value is based on grinding
with an abrasive sheet. Different applications may result in dif-
ferent values.
The noise and vibration values were determined according to
EN 60745-1 and EN 60745-2-3.
The specified vibration value was measured an the basis of a
standard test method and can be used to compare any kind of
power tools.
The specified vibration value can also be used for the initial
evaluation of exposure.
Warning! Depending on how you use the power
tool, the actual vibration values may deviate from
the specified values!
Take measures to protect yourself against vibra-
tions!
Make sure to take into account the entire work
process, i. e. also times when the power tool is
operated without Ioad or switched off! Appropri-
ate measures include the regular maintenance and
care of the power tool and its attachments, keep-
ing your hands warm, regular breaks and well
planned work processes!
220-240 V ~ 50 Hz
710 W
S1
800-1800 min
-1
M 14
Ø 225 mm
Ø 225 mm
II /
ca. 5,0 kg
91 dB(A)
102 dB(A)
3 dB
3,24 m/s²
1,5 m/s²