Before Use; During Use - Silva CROSS TRAIL 6X Bedienungsanleitung

FULL VERSION MANUAL
CROSS TRAIL 6X
Art. No: 37814
PRODUCT OVERVIEW
The Cross Trail 6X packaging consists of the following parts:
• Lamp unit
• Headband
• Extension cable with helmet strap
• Cable guide (side)
• Cable guide (rear)
• USB Rechargeable Battery 2.0 Ah
• USB cable
• Helmet bracket with adhesive strip
• Bike bracket
• Quick Guide

BEFORE USE

BATTERY CHARGING
1. Located on the side of the battery pack is a Micro-B connector.
Attach the included USB charge cable to this Micro-B connector.
2. Connect the USB connection to a wall outlet, computer or other standard USB connection.
3. Beneath the Micro-B connector there are 4 charge indication LEDs.
• During charge the LEDs shows its progress with one or more red lights.
• When fully charged all LEDs turns green.
Charge time is approximately 3 hours.
Note! When battery is fully charged the battery automatically switches to maintenance
charge. However, never leave a battery unattended while charging.
ADJUST THE HEADBAND
The headband is ergonomically shaped to give comfortable fit. Use the 2 buckle adjustments
to fit it perfectly to your head. Attach the headlamp in the head bracket by sliding the head-
lamp foot into the snap-in socket.
To remove, slide the headlamp up and out of the bracket.
FLEXIBLE BATTERY CARRYING
The battery pack can be carried in multiple ways; for example on the headband, in a pocket
backpack, on the waist using the extension cable and cable guide back, or mounted on the
bike frame by using the integrated Velcro strap.
MODULAR SYSTEM
In order to move the headlamp body from the headband to either the helmet bracket or the
bike bracket, gently push the lamp upward relative the head plate with head band. Insert the
headlamp body in the new bracket and gently press it down until you hear a click sound.
MOUNTING THE HELMET BRACKET
The helmet bracket comes with pre mounted adhesive on the back for easy mounting on any
helmet. The adhesive is a polyethylene foam tape developed to not damage or cause any
type of weakness to the plastic in your helmet.
Before mounting the helmet bracket on a helmet, make sure the surface is dry and clean.
Remove the protective paper from the adhesive tape on the helmet bracket. Gently press the
helmet bracket to the helmet.
Depending on helmet type, it might be preferable to use the non-flowligt mode which is when
the blue led on the headlamp is off (Helmet mode – Flow light deactivated), when the Cross
Trail 6X is used on a helmet.
MOUNTING THE BIKE BRACKET
The bike handlebar bracket is developed for use on bike handlebars with a dimension be-
tween 25 and 32 mm.

DURING USE

SILVA INTELLIGENT LIGHT® AND FLOW LIGHT
SILVA Intelligent Light® optimizes the light pattern by the unique combination of a long reach
spot light and a close flood light. With less head movements and a clear view of near as well as
far obstacles, you gain the balance and confidence it takes to move fast and perform better.
Our ingenious SILVA Flow Light takes the optimization even further by providing seamless
tuning of the light pattern for your favourite sport. Simply tilting the light downwards makes
the beams wider to brighten up slower activities. When tilting the headlamp upwards, the
light reaches longer to provide perfect vision when you move fast.
SWITCH ON YOUR HEADLAMP
A push button is located on the left side of the headlamp body. This button controls all light
modes.
• To start the headlamp with Flow Light activated press push button with a short press.
A blue led will be turned on which indicates that the flow light mode is on.
• To start the headlamp with Flow Light deactivated press and hold push button for 1
second
• To cycle between the different modes use short presses.
• To turn the headlamp off press and hold button for 1 second
SHORT PRESS
FLOW LIGHT ACTIVATED
MAX
FLOW LIGHT DEACTIVATED
OFF
DEACTIVATED FLOW LIGHT
Flow Light deactivated means that the Light image will remain unchanged even if the
headlamp is tilted up or down. This might be useful when the lamp is mounted on a helmet or
a bike handle bar.
TEMPERATURE CONTROL
The headlamp temperature will increase during use. The headlamp temperature is mainly
depending on light mode, ambient temperature and the airflow (speed). The Cross Trail 6X
headlamp is equipped with a temperature control function which prevents the headlamp
body from overheating by reducing the power to the LEDs. This means that the lower the
ambient temperature, the stronger the light output.
Note: Always make sure that the batteries are disconnected when the headlamp is stored in a
closed compartment such as a bag, pocket or similar.
BATTERY STATUS INDICATION (2.0. AH BATTERY)
When battery is connected to the headlamp and turned ON, current charge status is visible
for 30 seconds on the battery pack.
If you want to check battery status during use, the headlamp needs to be turned OFF and
then back ON.
LOW BATTERY WARNING
During operation of the headlamp there will be a low battery warning when 10% of the battery
energy remains. This is done by flashing both LEDs for 1 second and repeated again after 5
seconds.
POWER RESERVE MODE
During operation, the lamp will go into reserve mode when there is 10% power left of the
battery. All LEDs will flash once before the lamp goes into this mode.
Reserve mode can be overridden by pressing the button.
Warning: If you have pressed the button when headlamp is in reserve mode no more low
battery warnings will appear before the headlamp turns OFF.
LONG PRESS
MED MIN
OFF OFF