Functional Description - Makita DML801 Betriebsanleitung

battery pack may create a risk of fire when used with
another battery pack.
3. Use a power source with the voltage specified on the
nameplate of the charger.
4. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
5. Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
Let a hot battery cartridge cool down before charging
it.
6. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
7. After charging or before attempting any maintenance
or cleaning, unplug the charger from the power
source.
8. This battery holder part is not waterproof. Do not use it
in damp or wet locations. Do not expose it to rain or
snow. Do not wash it in water.
9. Do not touch the inside of the flashlight head with
tweezers, metal tools, etc.
10. Under abusive conditions, liquid may be ejected from
the battery, avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
11. Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive
material.
(2) Avoid storing battery cartridge in a container with
other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a breakdown.
12. If electrolyte gets into your eyes, rinse them out with
clear water and seek medical attention right away. It
may result in loss of your eyesight.
13. Be careful not to drop or strike battery.
14. Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
CAUTION:
1. When the tool is not in use, always switch off and
remove the battery cartridge from the tool.
2. Do not store the tool and battery cartridge in locations
where the temperature may reach or exceed 50°C
(122°F).
3. Do not give the tool a shock by dropping, striking, etc.
4. Do not expose the light to eyes continuously. It may
hurt them.
5. Do not cover or clog the lit tool with cloth or carton,
etc. Covering or clogging it may cause a flame.
6. Do not disassemble the charger or battery cartridge;
take it to a qualified serviceman when service or repair
is required. Incorrect reassembly may result in a risk
of electric shock or fire.
7. Use the tools only with specifically designated battery
packs. Use of any other battery packs may create a
risk of injury and fire.
6
8. If operating time has become excessively shorter, stop
operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
9. Do not use a damaged battery.
10. Charge the battery cartridge before completely
discharged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
11. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
12. If any problem develops, consult your nearest Makita
Service Center or dealer. To maintain product safety
and reliability, repairs, maintenance or adjustment
should be carried out by Makita Authorized Service
Center.
13. Charge the battery cartridge once in every six months
if you do not use it for a long period of time.
SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Charging
Charge the battery cartridge with the Makita charger
before use.
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the tool before installing or removing
of the battery cartridge.
• To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
• To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red indicator
on the upper side of the button, it is not locked
completely. Install it fully until the red indicator cannot
be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
• Do not use force when installing the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Battery protection system
The protection system is equipped, which automatically
cuts off the output power for its long service life. The light
goes off during operation when the remaining battery
capacity gets low. This is caused by the activation of
protection system and does not show the light trouble.
Remove the battery cartridge from the light and charge it.
Switch action (Fig. 2)
CAUTION:
• Do not look in the LED light or see the source of light
directly.
The LED light has a cycle of the three-ways status as
follows.