Inhaltsverzeichnis
Werbung
Anleitung_RT_TC_520_U_SPK1:_
6. Before using for the first time
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench, the base frame supplied in delivery, or
similar.
All covers and safety devices must be correctly
attached before the machine is used for the first
time.
The cutting wheel must rotate smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
7. Assembly and operation
7.1 Assembly (Fig. 1-6)
Fasten the feet (18) to the base frame (12) with
the 4 screws (19).
Turn the sub-frame upright.
Insert the two screws (37) for the trough fixture
through the square holes and place the trough
(3) in the base frame (12).
Fasten the cooling water pump (13) to the mount
(38). Place the tile cutter into the trough and
screw on the trough fixture (39).
Unscrew and remove the star handle screw (11)
and spacer (40) and keep them in a safe place.
Fill the trough with water until the cooling water
pump (13) is completely immersed.
7.2 RCD plug (Fig. 14)
Connect the RCD plug (37) to the power supply.
Press the reset button (38) and the control lamp
(39) will begin to shine. Press the test button (40)
to check the function of the RCD plug. If
everything is working properly the control lamp
(39) will go out and the contact to the power
supply will be interrupted. The RCD plug triggers
at a fault current of 30 mA. Defective RCD plugs
must be replaced by a qualified electrician.
Press the reset key (38) again in order to be able
to start up the machine.
7.3 ON/OFF switch (Fig. 7)
To switch on, press the "1" on the ON/OFF
switch (16).
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supplying
the cutting wheel with water.
To switch off, press the "0" on the switch (16).
17.02.2010
9:35 Uhr
Seite 13
7.4 90° Cutting (Fig. 8/9)
Loosen the star grip screw (27).
Set the angle stop (5) to 90° and retighten the
star grip screw (27).
Retighten the screws (28) to fasten the angle
stop (5).
Move the machine head (29) to the far end with
the handle (9).
Position the tile against the rail fence (6) on the
angle stop (5).
Switch on the tile cutting machine.
Caution: Always wait until the cooling water has
reached the cutting wheel (2) first.
Move the machine head (29) slowly and
smoothly forward through the tile with the handle
(9).
Switch off the tile cutting machine after
completion of cutting.
7.5 45° Diagonal cut (Fig. 10)
Set the angle stop (5) to 45°.
Cut as described in 7.4.
7.6 45° Lengthwise cut, "jolly cut" (Fig.11)
Loosen the star grip screw (10).
Tilt the guide rail (7) to the left to 45° on the
angle scale (17).
Retighten the star grip screw (10).
Cut as described in 7.4.
7.7 Changing the diamond cutting wheel
(Fig. 12/13)
Pull out the power plug.
Unscrew the four screws (35) and remove the
safety hood (8) for the blade.
Using the wrench (34), loosen the flange nut in
the direction of rotation of the cutting wheel (2).
(Caution: Left-hand screw-thread.) To do so,
place the wrench (31) on the motor shaft and
apply counterpressure.
Remove the outer flange (36) and cutting wheel
(2).
Clean the mounting flange thoroughly before
fitting the new cutting wheel.
Fit the new cutting wheel by following the above
procedures in reverse and then tighten.
Caution: Pay attention to the direction of rotation
of the cutting wheel!
Mount the safety hood (8) for the blade again.
GB
13
Werbung
Inhaltsverzeichnis
