Using Additional Handsets; Registering An Additional Handset; Select A Base; De-Register A Handset - Motorola D800 Serie Bedienungsanleitung

D811_IFU_EN.fm Page 19 Friday, September 7, 2007 8:01 PM
Downloaded from www.Manualslib.com

12. Using additional handsets

You can use up to five D801 additional handsets with your
D801 base to extend your phone system without needing to
install extension sockets for each new phone.
Your D801 handset can also be registered to up to 3 other
bases. You can then select the base you would prefer to use.
If you have purchased a D801 multiple pack any additional
handsets come pre-registered to the base.
If you have purchased an additional handset separately you
must register it to your D801 base before it can be used.

Registering an additional handset

At the base:
1. Press and hold
for 2 seconds until the base Power
p
starts flashing. The base will remain in registration mode for
90 seconds.
At the handset:
Please Register
1. If the handset is new and the display shows
Menu Registration Select
Press . Scroll to . Press .
u
Or
If the handset has already been registered to another base
Menu
the standby display is shown. Press , scroll or to
u d
Registration Select
and press .
Register Handset Select
2.
is highlighted. Press .
3. Bases are displayed. If necessary, scroll
or to a new
u d
base you wish to register your D801 handset to and press
Select
.
OK
4. Enter the system PIN and press
. (Default setting =
0000)
Searching Base X
5. The display shows
(where X is the chosen
Handset Registered
base number) then .
The handset is automatically assigned the next available
handset number.
If registration is not successful first time, please repeat the
process again in case the base registration period ran out of
time.
If there are already 5 handsets registered to the base, the
registration will fail. You must de-register another handset before
you can register the new one.

Select a base

If your D801 handset is registered to more than one base, you
can select which base to use.
Menu Registration Select
1. Press
, scroll or to and press .
u d
Using additional handsets
manuals search engine
Select Base Select
2. Scroll
to and press .
d
(In use)
3. All base numbers are displayed.
is added to bases
where the handset was previously registered to. Scroll
Select
or to the base you want and press .
d
Searching Base...
4. Display shows
. then the standby display for
that base.

De-register a handset

Use one handset to de-register another. You cannot de-register
the handset you are using.
Menu Registration
1. Press
, scroll or to and press
u d
De-register Select
2. Scroll
to and press .
d
OK
3. Enter the system PIN and press
. (Default setting =
0000)
4. Scroll
or to the handset you want to de-register and
u d
Select
press .
Yes No
5. Press
to confirm or to cancel.
Back
6. Press
to return to the previous menu level or
return to standby.
.

13. Help

Phone does not work
u
• Have you installed the batteries correctly?
• Check that the mains power is correctly connected.
No dial tone
• Is the telephone cord of the base plugged into the phone
socket?
• Check that the mains power is correctly connected to the
base and to the handset charger(s).
Select
.
• Only use the telephone cord supplied with the phone.
Cannot dial out or receive calls
• Check that the mains power is correctly connected.
• The batteries may need recharging.
• Has there been a power cut? If so, place the handset back
on the base for 10 seconds and try again. If it still does not
work disconnect the batteries and mains power for 10
to
> minutes, then reconnect and try again.
You have a dial tone, but the phone will not dial out
• You may need to change the dial mode from tone to pulse,
see page 12.
• If you are connected to a switchboard, check whether you
need to dial an access code.
Handset does not ring
• The ringer volume may be switched off, see page 11.
• Check that the mains power is correctly connected.
• Check that the line cord is connected.
• Make sure the handset is registered to the base, see
page 19.
No display
• The batteries may be flat, dead or incorrectly inserted.
Recharge or replace the batteries.
icon flashes
• Is the handset registered correctly to the base, see page 19.
• Check that the mains power is correctly connected.
• Check that the handset is within range of the base.
• The batteries are low, place the handset on the base/
charger to recharge.
icon not scrolling
• Try cleaning the charging contacts.
• Check that the mains power is correctly connected.
You hear the busy tone when you press
• Make sure the handset is in range of the base.
.
<
19