Braun MultiQuick 5 Vario Gebrauchsanweisung Seite 14

• Remove any bones, tendons and gristle from
meat to help prevent damage to the blades.
• Make sure the anti-slip rubber ring is attached to
the bottom of the chopper bowl.
Assembly and Operation
• Carefully remove the plastic cover from the blade.
• The blades (9b/9c) are very sharp! Always hold
them by the upper plastic part and handle them
carefully.
• Place the blade on the center pin of the chopper
bowl. Press it down and give it a turn so that it
locks into place.
• Fill the chopper with food and put on the lid (9a).
• For ice crushing, use the special ice blade (9c)
and fill up to 7 ice cubes into the chopper bowl.
• Align the chopper with the motor part (4) and
click together.
• To operate the chopper, switch on the appliance.
During processing, hold the motor part with one
hand and the chopper bowl with the other.
• Always chop harder foods (e.g. parmesan
cheese) at full speed.
• When chopping is complete, unplug and press
the EasyClick release buttons (5) to detach the
motor part.
• Lift the lid up. Carefully take out the blade before
pouring out the contents of the bowl. To remove
the blade, slightly turn it then pull it off.
Caution
• Do not use the chopper accessory to process
extremely hard foods, such as unshelled nuts,
coffee beans, grains, or hard spices e.g. nutmeg.
Processing these foods could damage the
blades.
• If using the appliance to purée hot food ensure
the liquid is not boiling. Allow hot food to cool
slightly to avoid risk of scalding.
• Only the «bc» chopper accessory (9) with the
special ice blade is allowed to crush ice cubes.
• Never place the chopper bowl in the microwave
oven.
Maximum rating is based on the MQ 20 chopper
«hc» that draws the greatest power and other
recommended attachments may draw significantly
less power.
«hc» Recipe example: Honey-Prunes (as a pancake
stuffing or spread)
50 g prunes
75 g creamy honey
70 ml water (vanilla-flavoured)
• Fill the «hc» chopper bowl with prunes and
creamy honey.
• Let it rest for 24 hours in refrigerator at 3°C.
• Add 70 ml water (vanilla-flavoured).
• Resume chopping for another 1,5 seconds at
maximum speed.
Use the chopper accessory «hc» (optional
accessory available at your Braun Service Center;
however not in every country).
14
Smoothie2Go accessory (D)
The Smoothie2Go is perfectly suited for preparing
fruit juices, smoothies and milkshakes. Furthermore
for cocktails and cool drinks with ice cubes. By
using the lid with drinking spout the mixing
container can also be used for take away.
Refer to the Processing Guide D for maximum
quantities, recommended times and speeds.
Before use
• The Smoothie2Go must only be operated by
using its special blade assembly (11a).
• Always attach blade assembly to mixing container
before attaching the motor part.
Assembly and Operation
• Fill the mixing container with ingredients.
• Then attach the blade assembly to the mixing
container turning it clockwise until it locks.
• Align the motor part and push the pieces together
until they click.
• Turn the assembled Smoothie2Go upside down,
plug in the appliance and choose Turbo speed
(3).
• Hold the motor part in one hand and support the
mixing container with the other hand.
• When finished blending, turn the mixing container
to its original position and unplug.
• Press the EasyClick release buttons (5) to detach
the motor part.
• Disassemble the blade assembly and use the lid
with drinking spout (11c) to close the
Smoothie2Go.
Tips for Best Results
• When mixing solid ingredients, cut them up into
small pieces of max. 2 cm.
• Always fill solid ingredients first into the mixing
container (11b).
• For particularly hard ingredients, it may be helpful
to start the device before turning to get the
maximum efficiency.
• If blending action stops during blending or
ingredients stick to sides of the mixing container,
there may not be enough liquid to blend
efficiently.
• Use the Turbo button (3) when mixing solid or
highly viscous ingredients to avoid the blade
becoming stagnant.
Caution
• Do not process carbonated or hot ingredients.
Allow hot liquids to cool to room temperature
before processing.
• Immediately stop operation and unplug the
appliance if liquids or parts of the processing
contents leak out.
• Avoid strong shaking, bumping or dropping when
in operation.
• Immediately stop operation when blade is
blocked. Disassemble and remove blockage
before continuing operation.