Warranty; General Safety Instructions - Gude SC 120 A Handbuch

GB Thank you for buying the gas welder Güde GE 120 W and for the trust in our products you
!!! Before you put the unit in operation, please, read this instruction manual carefully!!!
AV.1 Reprints, even if partial should be approved. Technical changes reserved
Any technical questions? Complaints? Do you need any spare parts or the instruction manual?
On your web page e www.guede.com, in section Servicing, you ma get a fast and non-beauorocraatic help. Please, help us to help you.
GB
For your unit to be identified in case of a complaint, we need the series number, year of manufacture and the ordering number. All the data
may be found on the plate. For you to keep them handy at any time, please write them down
Series number:
Phone: +49 (0) 79 04 / 700-360
Unit
Solid wire welding machine SG 120 A
Powder coated steel sheet case.
2 gearing stages, heat overloading protection
Switching time with forced circulation due to
cooling. Good for solid wits up to 0,9 mm (small
reel).
Outfit:
Including hoses directly connected, grounding
cables, terminal. welder´ s shield and brush.
Scope of Delivery (Fig. 1)
1. Solid wire welding machine SG 120 A
2. Welder's shield
3. Brush
5. Directly connected hose
6. Earthling terminal
Introduction
Solid wire welding
No additional gas is necessary for solid wire
welding. It is advantageous as the operator Is
more mobile and the gas in the wire is directed
directly in the arc and the unit is windproof when
used outdoors.
When the wire touches the piece worked an
electrical arc arises immediately. It is not a
defect.
When the hose is put into operation, only the wire
feed is activated, not the whole relay or ignition.
Set up the power of welding and the speed of
wire fee do get the dc arc and to hear harmonic
welding noise.
Otherwise: „Learning by doing"!
Is true
SG 120 A welding machine for solid wire
welding is a compact unit made according to
the latest technical parameters, owing to
which its reliability is high.
Minimum maintenance is sufficient to provide
long service life without any difficulties. Our
manual of use contains sufficient information on
installation and maintenance of these welding
units.
have shown.
Ordering number:
Fax: +49 (0) 79 04 / 700-51999
To reach a better result with he welding
machine, it is recommended to use a
protection welding spray to protect and
maintain nozzles and parts to be welded
(#24843). This is the way how to increase the
sealing properties and to decrease splashing
GB
EC Declaration of Conformity
We herewith declare, Birkichstraße 6, 74549 Wolpertshausen,
Germany
That the following Appliance complies with the appropriate
basic safety and health requirements of the EC Directive
based on its design and type, as brought into circulation by
us.
In a case of alternation of the machine, not agreed upon by
us, this declaration will loose its validity.
Machine description: Welding machine Date/Authorized
Signature:
Arnold, executive officer
Applied EU Directives
EU directive on machines 98/37/EG
-
- EU directive on low voltage 73/23/EWG
- EU directive on EMC 89/336/EWG EU 93/68/EEC
directive
Applied harmonised standards :
EN 60974-1:2005
EN 60974-10:2003
Place of certification :
TÜV Rheinland Product Safety GmbH
Am Grauen Stein
D-51105 Köln
Reference number :
15019498 001

Warranty

Claims according to the certificate of warranty
attached.

General Safety Instructions

The operating manual should be read entirely
before the first use. If in doubt regarding the
connection and operation, contact the
manufacturer (servicing department).
TO PROVIDE FOR A HIGH DEGREE OF
SAFETY, OBSERVE THE INSTRUCTIONS
BELOW CAREFULLY:
Care of additional security according to EN
947-3. Consult an expert electrician.
10
.
Year of manufacture :
E-mail: support@ts.guede.com