Symbols Used; Technical Data; Installation Instructions; Intended Use - Truma Mover XT4 Einbauanweisung

Table of Contents
Symbols used ................................................................... 10
Technical data ................................................................... 10
Installation instructions .................................................. 10
Intended use ........................................................................ 10
Approval .............................................................................. 10
Tools and facilities required ................................................ 10
Minimum installation dimensions ...................................... 11
Measuring the frame height ............................................... 11
Determining the installation type ........................................ 11
Special accessory installation ............................................. 11
Selecting a location ............................................................ 12
Mud guards ....................................................................... 12
Fitting the drive elements .............................................. 12
Electrical wiring and control unit ................................. 14
Connecting the battery ....................................................... 15
Connecting the safety socket ....................................... 15
Function check ................................................................. 16
Warnings ............................................................................. 16

Symbols used

The device must only be installed and repaired by an
expert.
Symbol indicates a possible hazard.
Note containing information and tips.

Technical data

Operating voltage
12 V DC
Power consumption
on average approx. 37 A up to a maximum of 150 A
Quiescent current consumption
< 80 mA (with plug / adapter inserted)
< 150 µA (plug / adapter disconnected or after 1 hour with
plug / adapter inserted)
Radio frequency
Class 2, 868 MHz
Speed
approximately 17 cm per second
(depending on weight and incline)
Weight
approx. 60 kg
Positive line fuse
150 A
Mover XT4 range of use
Dual-axle caravans with a gross weight of up to 3100 kg
Subject to technical changes.
EN
10

Installation instructions

Only competent and trained persons (experts) may in-
stall, repair and carry out the functional test on the Tru-
ma product in accordance with the installation and operating
instructions and the currently accepted technical regulations.
Experts are persons who, based on their specialist instruc-
tion and training, their knowledge and experience with Truma
products and the relevant standards, can carry out the neces-
sary work properly and identify potential hazards.
Please ensure that no metal chips or other contaminants get
into the control unit during installation.
In the case of screws with sealant, make sure that the
thread is free of grease / oil.

Intended use

The Mover XT4 has been designed for use on twin-axle cara-
vans with a gross weight of up to 3100 kg.
The Mover XT4 weighs approx. 60 kg.
Check the maximum towable weight for your towing
vehicle and the gross weight of your caravan to make
sure that they are designed for this additional weight.

Approval

The Truma Mover XT4 has design approval, and a "general
operating permit" (ABE) has been issued for Germany. Ac-
ceptance by a vehicle expert is not required (except when
installing the low chassis kit). The general operating permit
(ABE) must be kept in the vehicle.
The Mover XT4 complies with other requirements of
EC Directives and Standards (see Declaration of conformity).
When installing the Mover XT4, the technical and administrat-
ive regulations of the country of first registration of the vehicle
must be observed.
Any modifications made to the device, or the use of any spare
parts or functionally significant accessories other than original
Truma parts, or failure to comply with the contents of the op-
erating and installation instructions invalidates the warranty
and precludes any liability claims. This will also invalidate the
operating permit for the equipment.

Tools and facilities required

To install the Mover XT4 you need:
- 8 mm, 10 mm,13 mm and 17 mm socket wrenches,
ring spanners or open-jawed spanners
- Allen key 4
- Torque wrenches (3.5 - 50 Nm)
- Cable cutter / crimping tool
- Electric drill / screwdriver / keyhole saw, diameter 25 mm
- 2-tonne trolley jack and suitable support trestles
- Adequate lighting