Starting Operation; Maintenance And Service; Maintenance And Cleaning - Berner BACDVC 10.8V LI Originalbetriebsanleitung & Montageanleitung

OBJ_BUCH-2458-001.book Page 11 Friday, March 27, 2015 11:20 AM
Battery Charge-control Indication
The three green LEDs of the battery charge-control
indicator 3 show the charging status of the battery
5. The battery charge-control indicator only illumi-
nates for 3 seconds after start-up.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after switching on, then the
battery is defective and must be replaced.
Battery Insertion/Removal (see figures A1 – A2)
 Do not use force to insert the battery. The bat-
tery is designed in such a way that it can only be
inserted into the vacuum cleaner when it is in the
right position.
– Slide the battery 5 all the way into the battery
compartment 11.
– To remove the battery pack 5, press the unlock-
ing buttons 12 and pull the battery pack out of
the battery port 11.
Mounting the Crevice Nozzle
(see figure B)
 Remove the battery before cleaning or per-
forming maintenance on the vacuum cleaner,
making tool adjustments, changing accesso-
ries or storing the vacuum cleaner. This safety
measure prevents the vacuum cleaner from be-
ing started accidentally.
The crevice nozzle 9 can be connected directly to
the dust chamber 8.
– Firmly insert the crevice nozzle 9 into the intake
port 10 on the dust chamber 8 with the mark
shown in the illustration facing down.
Operation
 Remove the battery before cleaning or per-
forming maintenance on the vacuum cleaner,
making tool adjustments, changing accesso-
ries or storing the vacuum cleaner. This safety
measure prevents the vacuum cleaner from be-
ing started accidentally.
1 609 92A 16U • 27.3.15

Starting Operation

 Before vacuuming, ensure that the filter as-
sembly is assembled securely.
 Only use an undamaged filter (no cracks, small
Capacity
holes, etc.). Replace a damaged filter immedi-
≥2/3
ately.
≥1/3
Switching On and Off
<1/3
To save energy, only switch the vacuum cleaner on
Reserve
when using it.
– To switch on the vacuum cleaner, press the
On/Off button 2.
– To switch off the vacuum cleaner, press the
On/Off button 2 again.

Maintenance and Service

Maintenance and Cleaning

In all correspondence and spare parts orders,
please always include the 6-digit article number
given on the type plate of the vacuum cleaner.
 Remove the battery before cleaning or per-
forming maintenance on the vacuum cleaner,
making tool adjustments, changing accesso-
ries or storing the vacuum cleaner. This safety
measure prevents the vacuum cleaner from be-
ing started accidentally.
 For safe and proper working, always keep the
vacuum cleaner and ventilation slots clean.
– Clean the vacuum cleaner housing from time to
time using a moist cloth.
– Clean soiled charger contacts using a dry cloth.
Cleaning the Dust Cup (see figures C1–C3)
To maintain the optimum performance of the vacu-
um cleaner, clean the dust cup 8 after each use.
– Hold the vacuum cleaner down slightly so that
dust cannot fall out of the dust chamber when
the vacuum cleaner is opened.
– Press release button 1 and remove the dust cup
8 from the motor housing 7.
– Reach into the recess 13 on the motor housing
7 and pull the filter unit 15 off the motor housing
by the filter seal 14.
– Shake/tap out the dust cup 8 over a suitable
waste bin.
– If required, clean the dust cup with a moist cloth.
If required, clean the filter assembly (see "Clean-
ing the Filter Assembly", page 12).
– Insert the filter unit 15 with the filter seal 14 back
into the motor housing 7.
Afterwards, hang the dust cup at the bottom into
the motor housing, apply light pressure until the
dust cup can be heard to engage.
English | 11