Casals CAG13/125VCEK Handbuch Seite 4

- Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any ad justments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
- Store idle power tool out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dan gerous in the hands of untrained
users
- Maintain power tools. Check for misalignment or
bind ing of moving parts, breakage of parts and any
other con dition that may affect the power tool's op-
eration. If dam aged, have the power tool repaired
before use. Many acci dents are caused by poorly
maintained power tools
- Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control
- Use the power tool, accessories and tool bits etc.
in ac cordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dif-
ferent from those intended could result in a hazardous
situation.
Service
- Have your power tool serviced by a qualified re-
pair person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained
- Any misuse or failure to follow the instructions for use
renders the guarantee and the manufacturer's liability
null and void.
Safety warnings for angle Grinder
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive
Cutting-Off Operations
- This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations and
specifications provided with this power tool. Fail-
ure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
- Operation such as polishing is not recommended
to be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
- Do not use accessories which are not specifically
designed and recommended by the tool manufac-
turer.
4
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
- The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
- The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately guarded or controlled.
- Threaded mounting of accessories must match
the grinder spindle thread. For accessories mount-
ed by flanges, the arbour hole of the accessory
must be fit the locating diameter of the flange. Ac-
cessories that do not match mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
- Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive wheels
for chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped, in-
spect for damage or install an undamaged acces-
sory. After inspecting and installing an accessory,
position yourself and bystanders away from the
plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
- Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron ca-
pable of stopping small abrasive or workpiece frag-
ments. The eye protection must be capable of stop-
ping flying debris generated by various operations. The
dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged ex-
posure to high intensity noise may cause hearing loss.
- Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of work-
piece or of a broken accessory may fly away and cause
injury beyond immediate area of operation.
- Hold the power tool by insulated gripping surfac-
es only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
- Position the cord clear of the spinning accessory.
If you lose control of the power tool, the cord may be
cut o
into th
- Nev
has c
sory m
of you
- Do n
side.
could
your b
- Reg
motor
exces
of pow
- Do n
terial
- Do
ants.
electr
Kickb
- Kick
rotatin
sory.
rotatin
trolled
of the
ing. F
pinch
enteri
the m
The w
opera
ment
break
- Kick
correc
avoid
- Main
your
force
maxim
durin
tions
- Nev
sory.
- Do n
tool w
the to
the po
- Use
edge
cesso