Troubleshooting - Jacuzzi J-200 Serie Montageanweisung Und Bedienung Und Wartung

- To correct the situation:
I
Check that the water level is about 3 cm from the lowest hea-
drest. Add water if necessary.
I
Check for clogged/excessively dirty filter cartridge.
I
Eliminate any air locks from pump 1 by unscrewing the upper
drain plug for a few seconds. Then screw the plug back in.
I
If the problem persists, contact an authorized Jacuzzi service
centre.
The panel displays FL1 or FL2
(models with circulation pump)
If the message "FL1" flashes on the display it means that the flow
switch is not working perfectly, the cartridge of the filter is dirty or
there is air trapped in the circulation pump. A flashing "FL2" di-
splay means the pressure switch is not properly closed.
This error causes deactivation of the heater. Pump 1 might be
deactivated as well.
- To correct the situation:
I
Check that the water level is about 3 cm from the lowest hea-
drest. Add water if necessary.
I
Check for clogged/excessively dirty filter cartridge.
I
Eliminate any air locks from the circulation pump. Remove the fil-
ter cartridge and insert a garden hose in the housing of the cartridge.
Place a rag to seal the opening connected to the pump. Open the
water for about 30 seconds; then close it and put the filter back in
place. Check the operation of the spa.
I
If the circulation pump is not working, turn the main switch off
and on to prime it again.
I
If the problem persists, contact an authorized Jacuzzi service
centre.
The panel shows COL
The temperature has dropped 11°C below the set temperature.
Pump 1 (or the circulation pump, if included) and the heater
are activated to bring the temperature to 8 C° from the set tem-
perature.
I
No corrective action is required.
N.B.: this is a normal condition during the first filling of the spa, s-
ince tap water is often very cold. "COL" will only appear when the
spa is in Economy mode.
The panel shows ICE
Freeze Protection - A potential freeze condition has been detected.
I
No operation is required. The main pump (or the circulation
pump, if included) and the heater will activate to circulate warm
water through the plumbing until the pool is out of danger.
N.B.: "ICE" will only appear when the spa is in Economy mode.
Panel displays - - -
The safety software has been activated and the spa is deacti-
vated; a problem has been detected which may damage the
spa or its components.
I
Contact an authorized Jacuzzi Service Centre.

Troubleshooting

If the spa is not working the way it should, please first review
all the installation and operating instructions in this manual and
check the message on the panel display. If you are still not sat-
isfied it is working properly, please follow the troubleshoot-
ing instructions provided.
None of the components are working (pump, light)
Is there power to the spa?
Is the household circuit breaker tripped?
I
Contact an authorized Jacuzzi Service Centre.
Pump does not operate but light does
I
Press the "JETS" key. If the water remains still, check the le-
vel and make sure the spa is plugged in. If the problem persi-
sts, contact an authorized Jacuzzi service centre.
The main pump operates but no water flows from the jets.
Pump may not be properly primed.
This can happen after the spa is drained and refilled.
I
Press the JETS 1 button several times, never leaving the mo-
tor on for more than 5 to 10 seconds at a time.
Disconnect the power supply and unscrew the plug of the devi-
ator valve to let the air out and/or remove the filter. Ensure that
the deviator valve has been tightened and/or that the filter has
been re-installed before re-connecting the spa to the power
supply, then re-start the pump.
Poor jet action.
I
Press the JETS 1 button to make certain the pump 1 is on.
I
Place the air control in the "on" position.
I
Check that filter is not dirty and clean as necessary.
29