Mounting The Base Pieces With Casters; Before Getting Started; Getting Started; Cleaning - Silvercrest Z30399 Montage-, Bedienungs- Und Sicherheitshinweise

Assembly / Before getting started / Getting started / Cleaning
CAUTIon! DAnGER To lIfE, RISk of
InJURY AnD RISk of DAMAGE To
pRopERTY! Carefully read through the operat-
ing and safety instructions of your drill.
WARnInG!
DAnGER To lIfE! Make sure
that you do not hit electrical cables, gas or water
pipes when you drill into the wall. You may have to
check with a cable locator before you drill into the wall.
j
D rill four holes into the wall on which you want
to mount the electric heated towel rail
(ø 7 mm). Before doing so, measure the
distance required on the longitudinal struts of
the towel dryer .
16
CAUTIon! RISk of InJURY! Consult the
directions for use that came with your drill.
j
I nsert the decorative caps
the base pieces.
j
P lace the dowels
6
j
I nsert the phillips head self-tapping screws
into the retainers 3
dowels 6 (Fig. A).
j
I nsert the spacers
4
screw them tight onto the towel dryer using the
Allen screws (Fig. B).
1
j
P lace the electric heated towel rail
spacers onto the retainers
4
switch at the bottom) and screw them tight
17
using the Allen screws
note: Make sure that the screws have been
tightened and the towel dryer cannot fall down.
This could lead to damage to property or per-
sonal injury.
Mounting the base
Q
pieces with casters
j
F ix the decorative caps
wall assembly using the screws
note: Parts
,
10 11
("R" for right and "L" for left). Make sure that
the markings match up to one another during
assembly.
j
A ttach the base pieces
pieces to the electric heated towel rail
10
using the Allen screws
6 GB
16
into the holes for
12
into the boreholes.
2
and screw them into the
into the bushings and
5
with the
16
(ON/OFF-
3
(Fig. C).
7
into the holes for
8
(Fig. D).
9
and are marked
16
and the connecting
11
16
(Fig. E).
1
j
P lace the towel dryer onto a level surface.
note: Never use the electric towel drying
when the brakes are not on ("Free", Fig. G).
Before switching the appliance on, put the
brakes on the casters on ("Lock", Fig. H).

Before getting started

Q
B efore using the appliance for the first time,
check that the power supply corresponds to the
voltage specified on the appliance.
M ake sure that no-one can stumble over the
mains cable. Always make sure that the mains
cable goes behind the appliance.

Getting started

Q
j
I nsert the mains plug
j
S witch the electric heated towel rail
switching the ON/OFF switch
position. The red control light will come on and
the towel dryer will warm up.
j
H ang the towels onto the electric heated towel
rail as shown in Figure J.
16
note: So that the appliance does not overheat,
never hang the towels up so that they overlap
each other (Fig. I).
j
S witch the electric heated towel rail
ter using it or when it will not be in use for any
length of time by switching the ON/OFF switch
to the OFF position and removing mains
17
plug from the socket
will then go out.

Cleaning

Q
J CAUTIon! DAnGER fRoM
ElECTRIC SHoCk! Before clean-
ing, remove the mains plug from the
socket and always allow the appliance to cool
down completely.
j
O nly clean the outside of the appliance with a
soft, dry cloth.
O n no account should you use liquids or deter-
gents as they could damage the appliance.
into a socket.
13
on by
16
to the ON
17
off af-
16
. The red control light
13