Christopeit Sport TM 4 Handbuch Seite 22

USER MANUAL OF COMPUTER FOR 1352
1.1. Start
Normal startup after 3s counting backwards.
1.2. Number of programs
Manual Modes, 18 Preset programs, 3 User setting programs, FAT. Three
kinds of HRC mode .(3HRC)
1.3. Safe lock function
Remove the safety lock in any modes could rapidly slow down the tre-
admill till stop. "---" will be instantly displayed on the window, the buz-
zer buzz "Bi, Bi" sound continuously. Buttons are invalid in this condition.
When the safety lock is off, at the same time press „program" + „F" key for
3s, the display switches between imperial and metric systems.
Restore the safety lock, the window will display for 2s and then get into
standby state, wait for inputting commands.
1.4. Key function
START/STOP, PROGRAM,F, KM/H/+/-, STEIGUNG/+/-, SPEED SHORT-
CUT KEY: 2, 4, 6, 8, 10, 12.
INCLINE SHORTCUT KEYS: 2%, 4%, 6%, 8%, 10%, 12%, 15%.
"START/STOP" is the start/ stop key. Press "START/STOP" when the tre-
admill is in stop state, treadmill will be started and run at the lowest speed.
Press "START/STOP" when the treadmill is running, the treadmill will be
stopped.
"PROGRAM" stands for program key: in standby mode , press the key
you can select manual mode „1.0" to „P1-P18" and „U1-U3" and "HRC1-
HRC3"different programs ; manual mode is the default mode, the default
speed is 1.0KM/H, the max operating speed is 20km/h.
„F" stands for mode key, in standby mode, press the key you can loop set
H-1 to H-3 different countdown modes. H-1 is time countdown mode, H-2
is distance countdown mode, H-3 is calorie countdown mode; all mode
parameter can be setted by KM/H +/- key, and press „start" key to start
the treadmill.
Speed keys: "KM/H+" and "KM/H -" are accelerating and decelerating
keys: They may be used to adjust parameter setting when setting up pa-
rameters of the treadmill. When the treadmill is running, they are used to
adjust the speed for 0.1km/time; after holding for more than 2s, automatic
continuous acceleration and deceleration will be realized.
Incline key: "STEIGUNG+" and "STEIGUNG-" are incline increasing and
incline reducing keys: They may be used to adjust parameter setting when
setting up parameters of the treadmill. When the treadmill is running, they
are used to adjust the incline for 1 grade/time; after holding for more than
2s, automatic continuous increasing or reducing will be realized.
Speed shortcut keys: Speed can be directly adjusted to 2km/h, 4km/h,
6km/h, 8km/h, 10km/h, or 12km/h by speed shortcut keys when the tre-
admill is running.
Incline shortcut keys: Incline can be directly adjusted to grade 2, 4, 6, 8,
10, 12 or 15 by incline shortcut keys when the treadmill is running.
1.5. Display function
1.5.1. Speed display
Display the current running speed.
1.5.2. Time display
Display the running time under manual mode or the countdown running
time under mode and programmed mode.
1.5.3. Distance display
Display the accumulated distance under manual and programmed mode
or the countdown distance under mode running state.
1.5.4. Calorie display
Display the accumulated calorie under manual and programmed mode or
the countdown calorie under mode running state.
1.5.5 Heart rate display
Detect heat rate signals and display the pulse value.
1.5.6 Data display range of various parameters:
TIME: 0:00 – 99.59(MIN)
DISTANCE: 0.00 – 99.9(KM)
CALORIES: 0.0 – 999 (KC)
SPEED: 1.0 – 20.0(KM/H)
PULSE: 50 – 200 (BPM)
INCLINE: 0 – 15%
1.6. Heart rate measurement function
While the treadmill is connected to the power, hold the pulse tester for
5s and the heart rate value will be displayed. The initial value is the actu-
ally measured heart rate, and its display range is: 50-200 times/ minutes.
In the heartbeat measurement process, there will be a heart shaped icon
flashing.
Heart rate displayed is for reference only and can not be used as medical
data.
1.7. Manual Modes
1.7.1. How to enter manual mode:
A. Switch on the power supply; then, directly enter normal mode under
the manual mode.
B. In stop state, press F to select Normal mode, Time Countdown, Calo-
rie Countdown and Distance Countdown modes under the manual mode.
1.7.2. Setting functions under manual mode: Time, Distance and Calorie
Setting
A. When entering the manual mode, the time is displayed as 0:00;
B. In manual mode, press F to enter Time Countdown mode; the time
window will display the time and flicker; the initial time is 30:00; set count-
down time by KM/H +/ KM/H - and STEIGUNG +/ STEIGUNG -. Time set-
ting range: 5:00-99:00; each time of increase/ decrease will be 1: 00.
C. In time countdown mode, press F to enter Distance Countdown
mode; the initial distance will be displayed as 1.00 km; set the distance by
KM/H +/ KM/H - and STEIGUNG +/ STEIGUNG - in the range of 1.0-99.0
km/mi; each time of increase/ decrease will be 1 km.
D. In distance countdown mode, press F to enter Calorie Countdown
mode; the initial distance will be displayed as 50.0kcal; set the calorie by
KM/H +/ KM/H - and STEIGUNG +/ STEIGUNG - in the range of 20.0-990.0
kcal; each time of increase/ decrease will be 10.0 kcal.
1.7.3. Operation in manual mode:
A. Press START and the motor will start operating after 3s of countdown;
the initial speed will be 1.0km/h for metric system or 0.6mile/h for imperial
system;
B. Press KM/H +/ KM/H - to adjust speed;
C. Press STEIGUNG +/ STEIGUNG - to adjust the incline;
D. Press speed shortcuts to quickly set up to the speed marked on the
key;
E. Press incline shortcuts to quickly set up to the incline marked on the
key;
F. When the motor is running, press STOP and the motor will slow down
and stop finally;
G. Remove the safety lock to urgently stop motor running; then, LCD
window will display "---" and the buzzer will make short sound of Bi-Bi-Bi.
H. When the set time reduces to zero or when the set calorie reduces to
zero, or the set distance reduces to zero, the speed will gradually reduce
till the stop of the machine, the buzzer will make short alarm "Bi-Bi-Bi", and
the speed window will display END; 5s later, the machine will return to the
standby state and the buzzer will make long alarm "Bi-Bi";
I. Parameters not set will increase forwards, and will be reset after re-
aching the upper limit of the display range; in manual mode, the machine
will stop when the time accumulates to be more than 99: 59 (100min).
22