Werbung
IMPORTANT
Please read
these instructions carefully before you start to assemble this product.
Keep
these instructions
in
a
safe
place for
future
reference.
Customer
Service
For
assistance
with
assembly,
replacement
parts or any
other additional information
please log
onto our website
or
call
our customer service line (number
is
on
the title
page).
www.palramapplications.com
Safety advice
It
is
of utmost importance
to assemble
all
of the
parts according to the directions.
Do
not
skip any step.
We
strongly recommend
using
work
gloves during assembly.
Always wear shoes and safety
goggles when working with extruded aluminium.
If
using
a
step ladder or
power tools
ensure
that
you
follow the manufacturer
>s
safety advice.
Do
not touch overhead power
cables
with the aluminium
profiles.
Do
not attempt
to assemble the
product
in
windy
or
wet conditions.
Dispose
of
all
plastic bags safely keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not
lean
against or push the product during construction.
Do
not position your product
in an area
exposed to excessive wind.
Do
not attempt
to assemble this
product
if you
are
tired, have taken drugs or alcohol or if you
are
prone to dizzy
spell.
From safety reasons always use
the
lockers
for
each
position
(close,
open, ventilation, storage)
as
shown
in
step
33
Hot items such
as
recently
used grills,
blowtorches
etc.
must not
be stored
in
the
product.
Ensure
there
are
no
hidden pipes or cables
in
the ground before inserting the
pegs.
This
product
is
designed to
use
as
growhouse
only.
Care &
Maintenance
When your
product
needs to be cleaned,
use
a
mild detergent solution and rinse
with
cold
clean
water.
DO NOT use
acetone, abrasive cleaners or
other
special
detergents to
clean
the
clear panels.
Tools
&
Equipment
Tape measure
Work gloves
Lubricant
Phillips head screwdriver
Step
ladder
Drill
bit
Large
hammer
Spanner
T001
-
Special
tool for
Screws
411
and nuts 412
Al
Silicon spray
Before
Assembly
This
is
a
multi-part
assembly best achieved by
two
people.
Allow
at least
half
a
day for assembly process.
Selecting
a
site
-
the product must
be assembled,
positioned
and fixed
on
a
flat
level surface.
Choose
a
sunny position away from overhanging
trees.
Take
out
all
components
parts
of the
packages. Sort
the
parts and
check against
the contents
parts
list.
During assembly parts should
be laid
out
close at hand. Keep
all
small
parts (screws
etc.)
in
a
bowl
so
they
do
not get
lost.
Notice
Step
6
-
Make sure screws stay loose.
Step
7
-
Make sure screws
are
strongly tightened.
Step
8
-
If
trays are
dropping down when filled with
soil,
push
trays'frame
up and
tight
these screws again on
their
original position.
Step 27+28
-
make sure profiles
are
inserted
all
the way till the
end into plastic
connector.
Steps 32
-
If lid does
not located correctly
on
the frame
it
will not closed and
opened properly.
Try
re-checking
step
20 (measure) and
step 27+28
(insert profiles
all
the
way).
For easy
inserting of profile
960 use
lubricant
material or move
lid
up and
down.
Do
not
use
hammer.
Tighten
all
screws
when completing
assembly.
After
assembly
This
product's ground fixing
is
based on
soil
weight.
When trays
are
empty
it
should
be
kept from winds. There for we
are
strongly recommending fixing the
product directly
to
a
solid
concrete foundation.
Werbung
