Makita GA4040C Bedienungsanleitung Seite 6

Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding with normal side grip
Vibration emission (a
Uncertainty (K) :1.5 m/s
Work mode : disc sanding with anti vibration side
grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model GA4541C
Work mode : surface grinding with normal side
grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding with anti vibration side
grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model GA5041C
Work mode : surface grinding with normal side
grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding with normal side grip
Vibration emission (a
Uncertainty (K) :1.5 m/s
Work mode : disc sanding with anti vibration side
grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration emission value may also
be used in a preliminary assessment of exposure.
NOTE: The declared vibration emission value is used
for main applications of the power tool. However if the
power tool is used for other applications, the vibration
emission value may be different.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
2
) : 6.0 m/s
h,AG
2
2
) :2.5 m/s
h,DS
2
2
) : 2.5 m/s or less
h,DS
2
2
) : 6.5 m/s
h,AG
2
2
) : 5.5 m/s
h,AG
2
2
) : 2.5 m/s or less
h,DS
2
2
) : 2.5 m/s or less
h,DS
2
2
) : 7.0 m/s
h,AG
2
2
) : 6.0 m/s
h,AG
2
2
) : 2.5 m/s or less
h,DS
2
2
) : 2.5 m/s or less
h,DS
2
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Angle Grinder
Model No./ Type: GA4040C, GA4540C, GA5040C,
GA6040C, GA4541C, GA5041C
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for
future reference.
Grinder safety warnings
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
This power tool is intended to function as a
1.
grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions, illus-
trations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or
serious injury.
2. Operations such as polishing are not rec-
ommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause per-
sonal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can
be attached to your power tool, it does not assure
safe operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6 ENGLISH
1.2.2016
Yasushi Fukaya
Director