Brevi ALLROAD 511 Gebrauchsanleitung Seite 13

•
Never place the child car seat facing opposite the di-
rection of travel or sideways on the seat.
•
Never place any padding between the base of the child
car seat and the vehicle's seat, as this could impair the
safety of the child car seat.
•
Do not add to or modify this product, in any way.
•
Never use spare parts that are not recommended or
supplied by the manufacturer.
•
Should any unauthorized modification be made to this
child seat, its safety could be jeopardized; the manu-
facturer solely being authorized to make any modifi-
cation.
•
Do not leave a child unattended in the seat or in the
vehicle, at any time.
•
Never allow children to play with the child car seat.
•
Never install nor take out of the car this child seat with
your child in it.
•
This child car seat must not be used without the cover.
•
The seat cover should not be replaced with any other
than the one recommended by the manufacturer, since
the cover constitutes an integral part of this restraint.
•
Do not allow your child car seat to come into contact
with corrosive substances e.g. battery acid, solvents
etc.;
•
The buckle on the child car seat is not fully tamper pro-
of; - you should dissuade your child from playing with it.
•
Refrain from using it as a toy or as a seat at home.
•
Never use this product if it has been in an accident, or
if it has become badly worn.
In the event of an emergency
Press the red button on the buckle of the harness unit
(pic.16) to quickly release your child from the car seat
harnesses.
Warning: The buckle is an important component of
the child car seat; deter the child from playing with it.
If your child car seat has been involved in an accident
at a collision speed above 10 km/h, even though minor,
you MUST dispose of it and purchase a new one; even
if your child car seat shows no signs of damage, there
may be weaknesses that you are unable to see; if this
child car seat is involved in another accident it may fail
to protect your child. For this reason we suggest that you
NEVER use or purchase a second hand child car seat.
GROUP 1: 9 to 18 kg, pic. 2
ADJUSTING THE HARNESSES
Place the car seat adjusting it to the seat and make sure
that the harnesses are positioned correctly with respect
to the height of the child's shoulders (pic. 5).
To change the position of the harnesses, release the
two ends of the harnesses (pic. 7) from metal buckle F
behind the backrest (pic. 6), pull them off (pic. 8) and
pass them through the new slots (pic. 9); join them
again in the metal buckle F (pic. 10).
Stetch the harnesses to ensure they are installed cor-
rectly.
INSTALLATION FOR USE
Install the car seat once the harnesses are adjusted.
511-01-170203-00 istruzioni ALLROAD.indd 13
Ensure that the "seat" and the "backrest" are coupled
properly.
Do not use car seats in group 1 in the event of separate
seat and backrest.
The car seat must be secured by means of the car's
seat belt, as indicated in images 11 and 12.
Make sure that the car's seat belt is not twisted.
FASTENING THE HARNESSES
Place your baby in the car seat; fasten the harnesses by
joining parts "D1" and "D2" and inserting them in buckle
"D" until it clicks into position. (pic. 13).
Pull adjustment strap of harness unit "A" in the rear part
of the car seat , until the harnesses properly adhere to
the child's body in a comfortable way (pic. 14); to loosen
it, activate button "E" and proceed as shown in pic. 15.
The harnesses must be taut and not twisted.
Before any car trip, adjust the tautness of the harnesses
according to the baby's clothes. The adjustment with
winter clothing will be too loose in the summer.
Press the red button at the centre of the buckle (pic.
16) to release the baby from the harnesses.
GROUP 2: 15 to 25 kg, with backrest, pic.3
Remove the harness group before installing the car
seat. Use the belt guide with the car's seat belt.
REMOVING THE HARNESSES
To remove the harnesses, disconnect the two ends
"C1" and "C2" from element "F" (pic. 17); remove both
harnesses from the backrest, sliding them through the
slots of the backrest. Remove the crotch strap and the
shoulder straps passing the ends through the slots at
the base of the seat and in its lining (pic.17a, 17b, 18,
18a); hold down button "E" and remove everything pul-
ling upwards (pic. 19) whilst grasping element "F".
INSTALLATION FOR USE
Lay the seat on the car's seat, sit the baby down and
fasten the seat belt passing part "X" in the groove under
the armrest and over the baby's pelvis (pic. 20).
Stretch the car's seat belt and ensure it is not twisted.
Ensure that the diagonal part "Y" of the car's seat belt
rests correctly at the centre of the baby's shoulder.
Use belt guide "U" (positioning it in one of the slots on
the backrest and in correspondence of the baby's shoul-
der) passing the diagonal part "Y" of the car's safety
belt (pic. 21).
Insert the car's diagonal seat belt "Y" into guide "U" (pic.
22 pic23); finally, adjust by pulling the end of the band
that passes through the belt guide.
GROUP 2: 15 to 25 kg, without backrest, pic. 4
GROUP 3: 22 to 36 kg, pic. 4
Remove the harness unit before installing the car seat,
as shown in the previous chapter.
Remove the backrest and use only the seat.
To remove the backrest, remove the belt guide from the
slot, recline the backrest as shown in pic. 24 and pull it
off the seat (pic. 25).
13
07/03/2017 15.51.11