Basic Operation; Adjusting The Sound Quality - Pioneer DJM-900SRT Bedienungsanleitung

g COLOR control (page 16)
This changes the parameters of the SOUND COLOR FX of the different channels.
h Channel Fader (page 14)
Adjusts the level of audio signals output in each channel.
i CROSS FADER ASSIGN (A, THRU, B) selector switch (page 14)
Sets the output destination of each channel to [A] or [B].
j Crossfader (page 14)
Outputs audio signals assigned by the crossfader assign switch correspond-
ing to the curve characteristics selected by [CROSS FADER] (Crossfader Curve
Selector Switch).
k MASTER LEVEL control (page 14)
Adjusts the audio level output from the [MASTER1] and [MASTER2] terminals.
l Master Level Indicator (page 14)
Displays the audio level output from the [MASTER1] and [MASTER2] terminals.
m BALANCE control (page 15)
Adjusts the left/right balance of the sound output from the [MASTER1] termi-
nals, etc.
n MONO, STEREO selector switch (page 15)
Switches the sound output from the [MASTER1] terminals, etc., between mon-
aural and stereo.
o BOOTH MONITOR control (page 15)
Adjusts the level of audio signals output from the [BOOTH] terminal.
p EQ CURVE (ISOLATOR, EQ) selector switch (page 14)
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
q CH FADER (
, , ) selector switch (page 15)
Switches the channel fader's curve characteristics.
r CROSS FADER (
,
This switches the crossfader curve characteristics.
s ON/OFF (UTILITY) button
— ON/OFF: Turns the MIDI function on/off (page 17).
— UTILITY: Displays the [USER SETUP] or [CLUB SETUP] screen (page 24).
t START/STOP button (page 18)
Sends the MIDI start/MIDI stop signals.
u LFO FORM (WAKE UP) button
— LFO FORM: When [MIDI LFO] is selected at BEAT EFFECT, the MIDI signal's
waveform switches each time the button is pressed (page 20).
— WAKE UP: Cancels the auto standby mode.
v Main unit display
w X-PAD (page 17)
Adjusts the quantitative parameter of the BEAT EFFECT function.
x BEAT ,
buttons (page 16)
Set the beat fraction for synchronizing the effect sound.
y TAP (ENTER) button
— TAP: When the BPM measurement mode is set to [TAP], the BPM is input
manually by tapping the button with a finger (page 16).
— ENTER: Used to change this unit's settings (page 24).
z QUANTIZE button
When the QUANTIZE function is turned on for BEAT EFFECT, the effect is applied
to the sound without going off tempo when the currently playing track. (page 15).
A AUTO/TAP button (page 16)
Switches the BPM measurement mode.
B Beat effect selector switch (page 16)
Switches the BEAT EFFECT effect type.
C Effect channel selector switch (page 16)
Switches the channel to which the BEAT EFFECT is to be applied.
D TIME control (page 16)
Adjusts the BEAT EFFECT's time parameter.
E LEVEL/DEPTH control (page 16)
Adjusts the BEAT EFFECT's quantitative parameter.
F ON/OFF button (page 16)
Turns the BEAT EFFECT function on/off.
Do not pull on the channel fader and crossfader knobs with excessive force. The
knobs have a structure by which they cannot be pulled off easily. Pulling the knobs
strongly may result in damaging the unit.
14
En
, ) selector switch (page 15)

Basic Operation

Outputting sound
1 Press [POWER] button.
Turn on the power of this unit.
2 Switch the input selector switches.
Selects the input sources for the different channels from among the devices con-
nected to this unit.
— [DIGITAL]: Selects the DJ player connected to the [DIGITAL] terminals.
— [PHONO]: Selects the analog player connected to the [PHONO] terminals.
— [CD/LINE]: Selects the cassette deck or CD player connected to the [CD/
LINE] terminals.
— [USB]: Selects the sound of the computer connected to the [USB] port.
3 Turn the [TRIM] control.
Adjusts the level of audio signals input in each channel.
The corresponding channel level indicator lights when audio signals are being
properly input to that channel.
4 Move the channel fader away from you.
Adjusts the level of audio signals output in each channel.
5 Switch the [CROSS FADER ASSIGN (A, THRU, B)] selector
switch.
Switches the output destination of each channel.
— [A]: Assigns to [A] (left) of the crossfader.
— [B]: Assigns to [B] (right) of the crossfader.
— [THRU]: Selects this when you do not want to use the crossfader. (The sig-
nals do not pass through the crossfader.)
6 Set the crossfader.
This operation is not necessary when the [CROSS FADER ASSIGN (A, THRU, B)]
selector switch is set to [THRU].
7 Turn the [MASTER LEVEL] control.
Audio signals are output from the [MASTER1] and [MASTER2] terminals.
The master level indicator lights.

Adjusting the sound quality

1 Switch the [EQ CURVE (ISOLATOR, EQ)] selector switch.
— [ISOLATOR]: Functions as an isolator.
— [EQ]: The equalizer function is set.
2 Turn the [EQ/ISO (HI, MID, LOW)] controls for the respective
channels.
The adjustable ranges for the respective controls are as shown below.
— HI: –26 dB to +6 dB (13 kHz)
— MID: –26 dB to +6 dB (1 kHz)
— LOW: –26 dB to +6 dB (70 Hz)
Monitoring sound with headphones
1 Connect headphones to the [PHONES] terminal.
2 Press the [CUE] button(s) for the channel(s) you want to
monitor.
3 Switch the [MONO SPLIT, STEREO] selector switch.
— [MONO SPLIT]: The sound of the channels for which the [CUE] button is
pressed is output from the headphones output's left channel, the [MASTER]
channel sound is output from the right channel.
— [STEREO]: The sound of the channels for which the [CUE] button is pressed
is output from the headphones in stereo.
4 Turn the [MIXING] control.
This adjusts the monitor volume balance of the sound of channels for which the
[CUE] button is pressed and the sound of the [MASTER] channel.
5 Turn the [LEVEL] control for [HEADPHONES].
The sound of the channels for which the [CUE] button is pressed is output from the
headphones.
When the [CUE] button is pressed again, monitoring is canceled.