Specifications - Ingersoll-Rand 313 Gebrauschanweisungen

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
WARNING
Always wear eye protection
when operating or perform-
ing maintenance on this tool.
WARNING
Air powered tools can vibrate
in use. Vibration, repetitive
motions or uncomfortable po-
sitions may be harmful to your
hands and arms. Stop using
any tool if discomfort, tingling
feeling or pain occurs. Seek
medical advice before resum-
ing use.
WARNING
Keep body stance balanced
and firm. Do not overreach
when operating this tool.
These Sanders/Polishers will operate at the free
•
speed specified on the nameplate if the air supply
line furnishes 90 psig (6.2 bar/620 kPa) air
pressure at the tool. Operation at higher air
pressure will result in excessive speed.
Use only a sanding pad, buffing wheel or polishing
•
bonnet with these tools. Do not use any grinding
wheel, bur or metal removing accessory with these
tools. Never use an accessory having a maximum
LUBRICATION
Ingersoll- - Rand No. 10
Always use of an air line lubricator with these tools.
We recommend the following Filter- - Lubricator- - Regulator
Unit:
For International- - No. C28- - C4- - FKG0
For USA- - No. C28- - 04- - FKG0- - 28
Before starting the tool, unless an air line lubricator is
used, detach the air hose and inject about 1.5 cc of
Ingersoll- - Rand No. 10 Oil into the air inlet.
After every 150 hours of operation, remove the Bearing
Housing (35) and lubricate the Pinion (24) and Pinion
Gear (32) with 30 cc of Ingersoll- - Rand No. 67 Grease.
Model
313, 313- - EU
314, 314- - EU
Tested in accordance with ANSI S5.1- - 1971 at free speed
H
♦ Tested in accordance with ISO8662- - 1 sanding on steel workpiece
ISO3744
•
WARNING SYMBOL IDENTIFICATION
90 psig
(6.2bar/620kPa)
SANDER SPECIFIC WARNINGS
PLACING TOOL IN SERVICE
Ingersoll- - Rand No. 67

SPECIFICATIONS

Free Speed
rpm
5,000
5,000
WARNING
Always wear hearing
protection when operating
this tool.
WARNING
Do not carry the tool by the
hose.
WARNING
Operate at 90 psig (6.2 bar/
620 kPa) Maximum air pres-
sure.
operating speed less than the free speed of the
Sander/Polisher in which it is being used.
When using a pad having a shank, insert the shank
•
to full depth in the collet. When using a pad on a
threaded arbor, make certain the flange nut is
tightened securely. Check the tightness of the
collet nut or flange nut before operating a
Sander/Polisher to make certain it will not loosen
during operation.
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
REGULATOR
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
Spindle and
Back up Pad
Pressure
5/8" - - 11, 7" 99.3
5/8" - - 11, 7" 97.3
2
WARNING
Always turn off the air sup-
ply and disconnect the air
supply hose before install-
ing, removing or adjusting
any accessory on this tool,
or before performing any
maintenance on this tool.
Do not use damaged, frayed
or deteriorated air hoses
and fittings.
International Warning Label:
Order Part No. ___________
FILTER
COMPRESSOR
(Dwg. TPD905- -1)
HSound Level ♦Vibrations Level
dB (A)
•Power
112.3
110.3
WARNING
2
m/s
1.6
2.0