Cold Weather Operation - DeWalt DCFS950 Bedienungsanleitung

Inhaltsverzeichnis

Verfügbare Sprachen

EnGLIsh

5. Release the trigger and raise the stapler from the

work surface.

nOTE: The tool motor returns to full speed automatically

without the contact trip

6. Repeat steps 3–5 to actuate the next staple.

Multi-Angle Contact Trip (Fig. J)

The contract trip

has three notches to allow the user to locate

the wire depending on the desired angle they want to staple,

allowing the user to drive the staple at angle to the wood grain

up to 45 degrees.

Headlights/LED Indicator (Fig. A)

There are LED work lights

located on the front of the tool on

each side of the magazine.

LOW BaTTERY

Replace battery with a charged pack.

hOT Pack

Let the battery cool or replace it with a

cool pack.

JaM/sTaLL cOnDITIOn

Rotate the stall release lever to release.

Refer to Stall Release or Clearing a

Jammed Staple.

hOT TOOL (Both LEDs Flashing)

Let the tool cool down before

continuing use.

ERROR

Reset tool by removing and reinserting

battery pack or cycling trigger lock-off.

or any other

If error code persist, take tool to an

combination.

authorised D

Stall Release (Fig. K)

If the stapler is used in harder material where all available

energy in the motor is used to drive a fastener, the tool may

stall. The driver will not complete the drive cycle and the jam/

stall indicator will flash. Rotate the tool free stall release lever

on the tool and the mechanism will release.

nOTE: The tool will disable itself and not reset until the battery

pack has been removed and reinserted. If the driver does not

automatically return to the home position, proceed to Clearing

a Jammed Staple. If the unit continues to stall please review

the material and fastener length to be sure that it is not too

rigorous an application. The stapler could also be overheated

and needs time to cool before further use.

Clearing a Jammed Staple (Fig. A, L)

WARNING: To reduce the risk of serious personal

injury, disconnect battery pack from tool before

making any adjustments, changing accessories,

being depressed.

WALT service center.

servicing, or moving the tool. Such preventative safety

measures reduce the risk of starting the tool accidentally.

CAUTION: When removing a jammed staple, DO

NOT orient the stapler with the nose up or with the

battery foot up. Positioning the stapler this way makes

the jammed staple or pieces of the staple more likely to

be ingested into the stapler. If any portion of a staple is

ingested into the tool, the staple should be retrieved by

removing the top cap.

If a staple becomes jammed in the nosepiece, keep the tool

pointed away from you and follow these instructions to clear:

1. Remove battery pack from tool and engage trigger lock-off.

2. After laying the tool on its side, slide the spring-loaded

pusher

to the base of the magazine to lock it into place

and unload staple strip.

3. Rotate the magazine release

magazine

forward.

4. Remove jammed/bent staple, using pliers if necessary.

CAUTION: If any portion of a staple is ingested into

the tool, the staple should be retrieved by removing the

top cap.

5. If the driver is in the down position, rotate the stall release

lever on the top of the stapler.

nOTE: If the driver will not reset after rotating the stall

release lever, manually resetting the blade with a long screw

driver may be necessary.

6. Rotate the magazine back into position under the nose of

the tool and close the magazine release lever.

7. Reinsert battery pack.

nOTE: The tool will disable itself and not reset until the

battery pack has been removed and reinserted.

8. Reinsert staples into magazine (refer to Loading the Tool).

9. Release the pusher latch.

10. Disengage the trigger lock-off when ready to

continue stapling.

nOTE: Should staples jam frequently or the driver continually

fail to reset, have tool serviced by an authorised D

service centre.