Bostitch BTCN110 Bersetzt Von Den Originalanweisungen Seite 38

EngLIsh
2. Tip the tool up until the nails slide freely out of the side of
the magazine. Close sliding magazine fully.
3. Open the jam clear door on the nosepiece to verify there are
no nails remaining.
Mode Selection (Fig. A, D)
The finish nailer is capable of firing nails using bump actuation
or sequential actuation. Before operating this tool, look at the
selector switch to determine the actuation mode. Read all
instructions before selecting actuation mode.

WARNING: Keep fingers AWAY from trigger when not
driving nails to avoid accidental fastener discharge.
NEVER carry tool with finger on trigger. In bump mode
tool will drive a nail if contact trip is bumped while trigger
is depressed.
Sequential Action
Use sequential actuation mode for intermittent nailing where
very careful and accurate placement and depth control is
desired. The sequential actuation mode provides the maximum
delivery of power for driving the longest nails.
to operate the nailer in sequential actuation mode:
1. Slide the selector switch
icon .
2. Fully depress nosepiece against the work surface (motor
will start).
3. Pull trigger (nail will drive into work surface).
4. Release trigger.
5. Lift nosepiece off work surface.
6. Repeat steps 2 through 4 for next application.
NOTICE: The contact trip needs to be depressed followed
by a trigger pull for each nail followed by a release of both
the contact trip and trigger after each nail.
Bump Action
Bump action is intended for rapid nailing on flat, stationary
surfaces and typically most effective for applications that require
driving shorter nails.
When the tool is set in the bump actuation mode, two
methods of tool operation are available: place actuation and
bump actuation.
Slide the selector switch
8
to operate the tool using the place actuation method:

WARNING: A nail will be driven each time the trigger is
depressed as long as the contact trip remains depressed.
1. Depress the contact trip against the work surface.
2. Depress the trigger.
to operate the tool using the bump actuation method:
1. Depress the trigger.
2. Push the contact trip against the work surface. As long as
the trigger is depressed, the tool will drive a nail every time
the contact trip is depressed. This allows the user to drive
multiple nails in sequence.
36
8 to expose the single nail
to expose the triple nail icon

WARNING: Do not keep trigger depressed when tool is not
in use. Keep the trigger lock-off in the locked position when
the tool is not in use.

WARNING: When the tool's motor is running, pulling
the trigger or depressing the contact trip will cause a nail
to be driven.
Adjusting Depth (Fig. G)
The depth that the fastener is driven can be adjusted using the
depth adjustment wheel

WARNING: To reduce risk of serious injury from
accidental actuation when attempting to adjust
depth, ALWAYS:
• Remove battery pack.
• Engage trigger lock-off.
• Avoid contact with trigger during adjustments.
1. To drive the nail shallower
wheel 3 away from the nose of the nailer.
2. To sink a nail deeper
wheel 3 toward the nose of the nailer.
Headlights (Fig. H)
There is a headlight
Headlights turn on upon battery insertion, activation of
the trigger, or depressing the contact trip. The lights will
automatically shut off after 20 seconds unless tool remains
in use.
nOtE: These headlights are for lighting the immediate work
surface and are not intended to be used as flashlights.
Low battery indicator: The left-side headlight will flash four
consecutive times and then shut down to indicate low battery.
Jammed nail indicator: The right-side headlight will flash
continually if a nail becomes jammed in the nosepiece
(see Clearing a Stall or Jammed Nail).
Clearing a Stall or Jammed Nail (Fig. A, F, I)
If a nail becomes jammed in the nosepiece or the tool stalls,
the right-hand headlight will blink continuously. Keep the tool
pointed away from you and follow these instructions to clear:
1. Remove battery pack from tool and engage the trigger
lock-off.
.
2. Press the magazine latch
3. Lift the jam clear latch
nosepiece door.
4. Remove bent nail, using pliers if necessary.
5. If driver blade is in the down position, cycle the stall release
lever using enough force to fully slide it to the other end
12
of the slot in the housings.
6. Close the nosepiece door and engage the latch pin under
the two arms on the nosepiece. Push latch until it locks
in place.
7. Reinsert battery pack.
nOtE: The tool will disable itself and not reset until the
battery pack has been removed and reinserted.
on the side of the tool.
3
, rotate the depth adjustment
, rotate the depth adjustment
4 located on each side of the nailer.
16 and remove any loaded nails.
5 then pull up to open the