Playback Of Cd Or Audio Files (Usb, Cd); Programming Tracks And Files; Procedure With Audio Cd; Procedure With Audio Files - Kenwood M-918DAB-H Bedienungsanleitung

Connection of USB devices
1. Press the button to select standby mode.
2. Connect the USB device to the USB port on the front side.
Removal of the USB device
1. Press the button to select standby mode.
2. Remove the USB device from the USB port.
• Always wait until the device has completely read the CD/USB device before continuing.
• If no CD has been laid in the CD compartment, "NO DISC" will be displayed.
• If there is no playable audio file in the USB device, "NO SONG" will be displayed.
• The reading time can exceed 10 seconds with audio files if there is a great quantity of music
on a CD or USB device.

Playback of CD or audio files (USB, CD)

On the remote control: With the Source button, select the source and press the
begin playback.
On the main device: Using the
button, select the desired source and press the
begin playback
In USB devices or CDs which contain audio files (e.g. MP3), the number of folders present and the
27.0 mm
files will be displayed as follows:
4.5 mm
Fxx XXX
Here the number behind "F"stands for the number of folders and the second block of numbers for
the total number of files.
For audio CDs, the information about the number of tracks and total play time will be displayed as
follows:
XX XX:XX
Here the first block of numbers stands for the number of tracks and the second for the total play time
of the CD.
Basic Operating Functions
Stopping Playback: Press the button on the main device or on the remote control to stop
playback.
Interrupting Playback: Press the button on the main device or on the remote control to inter-
rupt playback. The display flashes during this. If you press the button one more time the playback
continues.
Searching for a specific passages during playback: Keep the
device or the remote control pressed down for longer than 2 seconds to activate fast rewind or fast
forward. As soon as the desired place is reached, release the relevant button again.
Selecting a specific track: Press the or
in playback, pause or stop mode.
Jump by 10 tracks: Press the or button on the remote control in playback, paus or stop
+10 -10
mode.
Selecting a specific folder (only with audio files): Press the
control to select a folder.
10
button to
button to
or button on the main
button on the main device or on the remote control
or button on the remote
Fold+ Fold-

Programming tracks and files

Using the remote control, you can programme tracks from an audio CD or files to play in the order
you desire. The following number of spaces in memory is available to you for this:
Audio-CD: 20 memory spaces

Procedure with audio CD

1. The "CD" source must be in Stop mode, otherwise "STOP FIRST" will show in the display.
2. Press the button to start the programming mode.
PRG
3. The display will now show "01 PR01" where "01" will be flashing. The first block of numbers
shows the current track, the second block of numbers shows the current storage space.
4. Using only the or button, select the track which you want to drop into the current storage
space.
5. Press the button to confirm the operation.
PRG
6. Afterwards the next storage space will be displayed. Repeat steps 4 and 5 until your selection is com-
pleted or the complete number of memory spaces in occupied. In this case, "Full" will be displayed.
7. With the button, you can start playback of the programmed tracks. During playback
the number of the track and that of the programme space will be alternately displayed.
8. Pressing the button twice deletes the programming.

Procedure with audio files

1. The "USB" source must be in Stop mode, otherwise "STOP FIRST" will show in the display.
2. Press the button to start the programming mode.
PRG
3. The display will now show "01 PR01" where "01" will be flashing. The first block of numbers
shows the current track, the second block of numbers shows the current storage space.
4. Using the or button, select a folder or retain the current folder. When a folder has
Fold+ Fold-
been selected, the display changes to "Fxx XXX"
for the current track.
5. Using only the or button, select the track which you want to drop into the current storage space.
6. Press the button to confirm the operation.
PRG
7. Afterwards the next storage space will be displayed. Repeat steps 4 and 6 until your selection is com-
pleted or the complete number of memory spaces in occupied. In this case, "Full" will be displayed.
8. With the button, you can start playback of the programmed tracks.
9. Pressing the button twice deletes the programming.
• If the button is pressed during playback the process is interrupted. Turning off
the device deletes any programme which is present.
Files: 99 memory spaces
. Here, "Fxx" stands for the current folder and "XXX"
11