Operating - DeWalt DWS773 Bersetzt Von Den Originalanweisungen

Adjustments and Replacements
The Mitre Saw was accurately adjusted at the factory. Due to shipping
and handling or any other reason a readjustment can be required.
WARNING: Electrical shock can cause serious injuries or dead
• Before work: Disconnect the power cable from the power supply.
NOTICE:
• Ensure that the arm is securely fixed when performing bevel cuts.
• Check that the blade does not touch the table at the rear of the slot or at
the front of the rotating arm at 90° vertical and 45° bevel positions.
• If the saw blade is worn, replace it with a new sharp blade.
• Check the technical data of the new blade: Use 216 mm saw blades with
30 mm arbor holes to obtain the desired cutting capacities.
• Replace the kerf plate when worn. If the kerf plate becomes worn or
damaged take saw to an authorised service centre.

Operating

General
• Use the optional roller tables for large and long pieces of wood.
• Use the optional dust extraction.
• Never use your saw without the kerf plate.
Before use
• Check for damage to the tool and the power cable. Take care that
the power supply cord is not placed in the cutting area
• Check the upper blade guard, movable lower blade guard as well as
the dust extraction tube to determine that it will operate properly.
• Check the lower blade guard , it is designed to close quickly when
the lever is released. If it does not close within 1 second, have the
saw serviced by an authorized D
• Ensure that chips, dust or workpiece particle cannot lead to blockage
of one of the functions.
• In case of workpiece fragments jammed between saw blade and
guards disconnect the tool from the power supply. Remove the
jammed parts and reassembling the saw blade.
• Allow the blade to cut freely. Do not force.
• Always make dry runs (without power) before finish cuts so that you
can check the path of the blade.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
WARNING: Improper use can cause serious harm.
• Be sure that the tool is in the "off" position before plugging in.
• Do not let persons, especially children, not involved in the work,
touch the tool or the extension cord and keep them away from
the work area.
Body and hand position
• Never place your hands closer than 100 mm from the blade.
• Never cross your hands.
42
WALT repair agent.
e
• As you move the saw arm left and right, follow it and stand
slightly to the side of the saw blade.
Cutting
• Always let the blade come to a full stop before raising the arm.
If small fibres of wood still split out at the rear of the workpiece,
stick a piece of masking tape on the wood where the cut will be
made. Saw through the tape and carefully remove tape when
finished.
• Hold the workpiece tightly to the table and the fence when
cutting. Keep your hands in position until the switch has been
released and the blade has completely stopped.
• When mitring the end of a piece of wood with a small off-cut,
position the wood to ensure that the off-cut is to the side of the
blade with the greater angle to the fence, i.e:
-
left mitre, off-cut to the right
- right mitre, off-cut to the left
After use
• Disconnect the power cable from the power supply.
• Store the Mitre Saw in a dry place and locked up securely, out of
reach of children.
Dust Extraction
WARNING: Risk of dust inhalation. To reduce the risk of personal
injury ALWAYS wear approved dust mask.
WARNING: ALWAYS use a vacuum extractor designed in
complaince with the applicable directives regarding dust emission
when sawing wood.
• Certain dusts, such as oak or beech dust, are considered as
carcinogenic.
• Observe the relevant regulations in your country for the materials to
be worked.
NOTICE:
• Connect the saw to a dust collection device when sawing wood. Always
consider factors which influence exposure of dust such as:
ʵ good ventilation of the working place;
ʵ sharpness of the saw blade;
ʵ correct adjustment of the saw blade,
ʵ Push the saw through the workpiece. Do not pull the saw through
the workpiece.
Cleaning and Maintenance
The Mitre Saw requires no additional lubrication and has been designed
to operate over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: Electrical shock can cause serious injuries or death.
• Before cleaning: Disconnect the power cable from the power
supply.
NOTICE:
• Use a cloth dampened only with water and mild soap.
• Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.