Herunterladen Inhalt Inhalt Diese Seite drucken

Chicco Key23 Gebrauchsanleitung Seite 36

Vorschau ausblenden Andere Handbücher für Key23:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 24
4. Remove the fabric cover from the frame
(diag. 28).
To replace the fabric cover onto the frame,
repeat operations 1,2,3,4 in the reverse order,
paying special attention that the fabric cover
fits and adheres correctly to the frame.
Seat
The seat is formed of two rigid plastic parts
hooked to each other.
To remove the fabric cover from the seat, it is
first necessary to release the upper part from
the fixed lower part:
1. Insert a finger into the slot on the seat and
press the button inside, following the in-
structions provided in the "Adjusting the
reclining backrest" paragraph (Fig. 29).
2. Turn the 4 handles, until they coincide with
the OPEN symbols (diag. 30).
WARNING! At the end of the operation,
check that the small reference circles, lo-
cated on the base, and the handles are
aligned, and that the two parts are correctly
unlocked.
3. Position the child car seat as shown in diag. 31,
and raise the backrest to the highest position.
4. Raise the upper part of the child car seat,
removing at the same time the rear panel
of the backrest (diag. 32).
5. Release the fabric cover, by unfastening the
5 press-studs located on the base (diag. 33).
6. Remove the cover from the upper part of
the seat (diag. 34).
To replace the fabric cover onto the frame:
7. Repeat operations 4,5,6 in the reverse order,
ensuring that the fabric cover fits onto and
adheres correctly to the frame, in particular
in the red areas, which coincide with the
lap belt holes.
8. Press the button whilst pulling the rear recline
adjuster handle, as illustrated in Fig. 35.
9. Place the child car seat as shown in diag. 36,
and raise the backrest to he highest position.
10. Replace the upper part of the seat onto the
lower fixed part: to insert the upper part
more easily, it is recommended to recline
the upper part during the operation, as
shown in diag. 37.
WARNING! At the end of the operation, check
that the two parts coincide.
11. Re-insert the rear panel between the frame
and the fabric cover (diag. 38).
12. Place the child car seat onto a flat surface,
as shown in diag. 39, and turn the 4 handles
to the CLOSE symbols (diag. 40).
WARNING! At the end of the operation, check
that the small reference circles, located on the
base and the handles, are aligned, and that the
two parts are locked correctly.
How to Release the Backrest /Seat
The child car seat can be used in the car only
WITH the backrest fitted onto the seat cor-
rectly.
The backrest can be released and removed
from the seat ONLY for reasons of space, when
not in use.
To release the backrest from the seat:
1. Pull out the seat inclination adjuster handle
to the third position; following the instruc-
tions contained in the paragraph "How to
Adjust the Inclination of the Backrest".
2. Exercise some pressure onto the backrest
towards its rear part, in the position where
the joint is fitted to the seat, and release the
two locking devices (diag. 41).
To fit the backrest onto the seat, repeat the op-
erations described above in the reverse order.
WARNING! At the end of the above operations,
check that the upper and lower parts of the
seat are correctly locked to each other.
WARRANTY
The product is guaranteed against any con-
formity defect in normal conditions of use as
provided for by the instructions for use.
The warranty shall not therefore apply in the
case of damages caused by improper use,
wear or accidental events.
For the duration of warranty on conformity
defects please refer to the specific provisions
of national laws applicable in the country of
purchase, where provided.
36

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis