Product Description And Specifications - Bosch GPO 950 Professional Originalbetriebsanleitung

GPO 950_160992A3S8.book Page 14 Tuesday, May 15, 2018 4:15 PM
14 | English
 Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory. Cor-
ners, sharp edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
 Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent kickback
and loss of control.
Safety warnings specific for polishing operations
 Do not allow any loose portion of the polishing bonnet
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
Additional safety warnings
Wear safety goggles.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled. This pre-
vents uncontrolled restarting.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for polishing metal and coated sur-
faces.
1 609 92A 3S8 | (15.5.18)
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Thumbwheel for speed preselection
2 Lock-on button for On/Off switch
3 On/Off switch
4 Auxiliary plate
5 Auxiliary handle (insulated gripping surface)
6 Adapter M14
7 Adapter M16
8 Stick pad (M16)
9 Plane sponge pad
10 Lamb's wool pad*
11 Corrugated sponge pad*
12 Polishing plate with sponge pad*
13 Open-end spanner (2x)
14 Handle (insulated gripping surface)
15 Direction-of-rotation arrow on housing
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Polisher
Article number
Rated power input
Output power
Max. speed
Speed control adjustment
Polishing plate diameter, max.
Adapter thread size
Soft starting
Speed preselection
Constant electronic control
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 80 dB(A); Sound power level 91 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
2
Polishing: a = 7.5 m/s , K= 1.5 m/s
h
GPO 950
3 601 CA2 0..
W 950
W 539
-1
min 2100
-1
min 600 – 2100
mm 180
M14/M16



kg 2.3
/II
2
.
Bosch Power Tools