Operation - EINHELL TC-SM 216 Originalbetriebsanleitung

5.3 Adjusting the saw (Fig. 1-3)
•
To adjust the turntable (19), the locking lever
(20) must be in the top position. Only then is it
possible to adjust the turntable while holding
the release button (21) pressed down. (see
Fig. 5)
•
Turn the turntable (19) and scale pointer (22)
to the desired angular setting on the scale
(23).
•
The saw has locking positions at angles of -
45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30° and
45°, at which the turntable (19) audibly clicks
into position. Once the turntable is engaged,
the setting must be additionally secured by
pressing the locking lever (20) down.
•
If different angle settings are required, the
turntable (19) may be secured in position
using only the locking lever (20).
•
To release the saw from its position at the
bottom, pull the retaining pin (30) out of the
motor mounting while pressing down lightly
on the machine head (4).
•
Swing up the machine head (4).
•
When the locking grip (26) is undone, you
can tilt the machine head (4) to the left by up
to 45°. After the desired angular setting has
been set on the scale pointer (24) on the sca-
le (25), secure the machine head (4) again
with the locking grip (26).
•
To ensure that the saw is standing securely,
adjust the adjustable foot (17) by turning it so
that the saw stands in a horizontal and firm
position.
•
The machine head (4) can be moved back-
wards and forwards using the drag function.
To prevent the drag function, the guide rails
can be fixed in a specific position with the
locking screw (29).
5.4 Precision adjustment of the stop rail
(Fig. 6, 7)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (7) and the stop rail (13).
•
Slacken the four adjustment screws (44)
using a hex key, set the stop rail (13) to 90° in
relation to the saw blade (7) and retighten the
adjustment screws (44).
•
The angle stop (a) and hex key (5 mm) are
not included in the scope of this delivery.
Anl_TC_SM_216_SPK9.indb 29 Anl_TC_SM_216_SPK9.indb 29
GB
5.5 Precision adjustment of the angle stop for
crosscut 90° (Fig. 8, 9)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the right to 0° using
the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (35) until the angle between
the blade (7) and the turntable (19) equals
90°.
•
Retighten the lock nut (37) to secure this
setting.
•
Finally, check the position of the pointer (24).
If necessary, release the pointer with a cros-
stip screwdriver, move to the 0° position of the
angle scale (25) and retighten the pointer.
•
The angle stop (a) and crosstip screwdriver
are not included in the scope of this delivery.
5.6 Precision adjustment of the angle stop for
miter cut 45° (Fig. 8, 10)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (36) until the angle between
the blade (7) and the turntable (19) equals
exactly 45°.
•
Retighten the lock nut to secure this setting.
•
No angle stop (b) included.

6. Operation

Warning! To make 90° crosscuts, the adjustable
stop rail (14) must be fi xed at the inner position:
•
Undo the locking grip (15) for the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (14) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (14) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
- 29 -
24.04.2019 09:30:47 24.04.2019 09:30:47