Technical Data; Operation; Before Starting - EINHELL NEW GENERATION NFF 1200 Bedienungsanleitung

Anleitung_NFF_1200_SPK7:_
GB

5. Technical data

AC motor
Rating
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Weight
Dust extraction connector
For use as a crosscut and miter saw
Swiveling range
Miter cut
Saw width at 90°
Saw width at 45° (turntable)
Saw width at 45° (angle)
Saw width at 2 x 45° (double miter cut) 42 x 100 mm
For use as a bench circular saw
Size of bench
Max. cutting height
Height adjustment
Tilting saw blade
Operating mode S1: Continuous operation
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of the
cycle.

6. Before starting

Pull the power plug before performing any
adjusting, conversion and assembly work.
The machine has to be set up where it can stand
securely.
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the blade to run freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws, etc.
Before you press the ON/OFF switch check that
the saw blade is fitted correctly and that moving
parts move easily.
26
14.01.2009 11:10 Uhr
Before you connect the machine to the mains
supply make sure that the data on the model
plate are identical to the mains data.
230 V ~ 50 Hz
1200 W
6.1 Assembling the machine (Fig. 3 – 9)
S6 40 % 1. Lift the machine out of the packaging and remove
the four plastic protective caps (Fig. 3). These are
3200 rpm
for transit purposes only and can be disposed of.
Ø 205 x Ø 30 x 2.5 mm
2. Pull up the holder bar (Fig. 4 / Item 21) and unfold
24
the bottom frame as shown in Figures 5 – 6.
36 kg Ensure that all four locking bars (Fig. 6+7 / Item
22) lock into position. Follow the instructions
Ø 36 mm
above in reverse order to fold up the bottom
frame. Ensure that the appropriate locking bars
are released for folding (Fig. 8).
Up to 45° to the left
3. On uneven surfaces the saw can be assembled
to be stable using the adjustable foot (Fig. 9 / Item
+45° / 0° / -45°
23). There are lugs on the other three feet using
55 x 130 mm
which the saw can be anchored securely to the
55 x 90 mm
surface.
42 x 110 mm

7. Operation

7.1. General control elements (Fig. 10-12)
400 x 430 mm
45 mm ON/OFF switch
Press in the sides of red push-button to open the
0 - 45 mm infinite
switch cover (Fig. 10).
0° - 45° to the right
To switch on:
Press the green button (I) (Fig. 11)
To switch off:
Press the red button (0) (Fig. 11)
Emergency Stop function:
Press the red button (flap) (Fig. 12)
To prevent the machine being started without
authorization, the closed flap can be secured with a
padlock (not supplied).
Motor circuit-breaker:
In the event of an overload (for example if the saw
blade stops) the motor circuit-breaker will cut out
automatically.
The saw can be switched on again by pressing the
green button (I).
Zero voltage switch:
The saw is fitted with a zero voltage switch to prevent
it from restarting after a voltage failure. Press the
green button (I) to switch it on again.
Seite 26