Specifications - Denon AVR-1803 Bedienungsanleitung

ENGLISH
Symptom
• Batteries dead.
• Remote control unit too far from
this unit.
This unit does not operate
• Obstacle between this unit and
properly when remote control
remote control unit.
unit is used.
• Different button is being pressed.
• < and > ends of battery inserted in
reverse.
NOTE:
When a subwoofer has been connected and the virtual surround function is being used, the signal played from
the subwoofer channel is LFE only (only when playing Dolby Digital or DTS signals) for initial factory settings
(i.e., the setting of the front speaker is "LARGE" and the setting of the subwoofer mode is "NORM").
When subwoofer effects are felt to be weak, try setting the subwoofer mode to "+MAIN", or the front
speaker to "SMALL" in the System setup "Speaker Configuration" settings.
Making these settings will result in the low-frequency sounds of the front channel being played from the
subwoofer.

20 SPECIFICATIONS

2 Audio section
• Power amplifier
Rated output: Front:
Center:
Surround: 80 W + 80 W
Surround Back:
Dynamic power: 100 W x 2 ch
145 W x 2 ch
170 W x 2 ch
Output terminals: Front/Center/Surround:
Surround Back:
• Analog
LINE input - PRE OUT
Input sensitivity/input impedance: 200 mV/47 kΩ/kohms
Frequency response: 10 Hz ~ 100 kHz: +1, –3 dB (DIRECT mode)
S/N ratio: 100 dB (IHF-A weighted) (DIRECT mode)
Distortion: 0.008% (20 Hz ~ 20 kHz) (DIRECT mode)
Rated output: 1.2 V
• Phono equalizer (PHONO input — REC OUT)
Input sensitivity: 2.5 mV
RIAA deviation: ±1 dB (20 Hz to 20 kHz)
Signal-to-noise ratio: 74 dB (A weighting, with 5 mV input)
Rated output / Maximum output: 150 mV / 7 V
Distortion factor: 0.03% (1 kHz, 3 V)
34
Cause Measures
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
80 W + 80 W
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
80 W
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
110 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
80 W
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
110 W
(8 Ω/ohms)
(4 Ω/ohms)
(2 Ω/ohms)
16 to 16 Ω/ohms
A or B 16 to 16 Ω/ohms
A + B 12 to 16 Ω/ohms
2 Video section
Page
• Standard video jacks
9 Input/output level and impedance:
9
Frequency response:
• S-video jacks
9
Input/output level and impedance:
—
Frequency response:
9
• Color component video terminal
Input / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
Frequency response:
2 Tuner section
Receiving range:
Usable sensitivity:
50 dB quieting sensitivity:
S/N ratio:
Total harmonic distortion:
2 General
Power supply:
Power consumption:
Maximum external dimensions:
Mass:
2 Remote control unit (RC-917)
Batteries:
External dimensions:
Mass:
For purposes of improvement, specifications and design are subject to change without notice.
1 V p-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
(blue) signal — 0.7 Vp-p, 75 Ω/ohms
P /C
B B
(red) signal — 0.7Vp-p, 75 Ω/ohms
P /C
R R
5 Hz ~ 27 MHz — +1, –3 dB
[FM] (note: µV at 75 Ω/ohms, 0 dBf = 1 x 10 –15
W)
87.50 MHz ~ 108.00 MHz
1.0 µV (11.2 dBf)
MONO 1.6 µV (15.3 dBf)
STEREO 23 µV (38.5 dBf)
MONO 80 dB (IHF-A weighted)
STEREO 75 dB (IHF-A weighted)
MONO 0.15 % (1 kHz)
STEREO 0.3 % (1 kHz)
AC 230 V, 50 Hz
260 W
1 W Max. (Standby)
434 (W) x 171 (H) x 417 (D) mm
11.7 kg
R6P/AA Type (two batteries)
55 (W) x 225 (H) x 34.5 (D) mm
165 g (including batteries)
[AM]
522 kHz ~ 1611 kHz
18 µV