Specifications; General Safety Rules - Makita 3612 Betriebsanleitung

ENGLISH
1 Wrench
2 Router bit
3 Shaft lock
4 Tighten
5 Loosen
6 Nylon nut
7 Stopper pole
8 Fast-feed button
9 Lock lever
10 Adjusting hex bolt
11 Stopper
12 Stopper pole
13 Chip deflector
14 Adjusting hex bolt
15 Hex nut
16 Stopper
17 Switch lever
18 Lock-off button
19 Switch trigger
20 Speed change knob

SPECIFICATIONS

Model
Collet capacity ............................................................... 12 mm or 1/2''
Plunge capacity ............................................................. 0 – 60 mm
–1
No load speed (min ) .................................................. 22,000
Overall heigth ................................................................ 297 mm
Base diameter ............................................................... 160 mm
Net weight ..................................................................... 5.8 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.32 Ohms it
can be presumed that there will be no negative
effects.
The mains socket used for this device must be pro-
tected with a fuse or protective circuit breaker having
slow tripping characteristics.
6
Explanation of general view
21 Workpiece
22 Bit revolving direction
23 Feed direction
24 View from the top of the tool
25 Correct bit feed direction
26 Straight guide
27 Guide holder
28 Fine adjusting screw
29 Wing bolt (B)
30 Wing bolt (A)
31 Stright guide
32 More than 15mm
33 Straight guide
34 Wood
35 Trimmer guide
36 Wing bolt (A)
37 Guide roller
38 Guide holder
39 Fine adjusting screw
40 Wing bolt (B)
3612
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
Work area safety
1.
2.
3.
Electrical safety
4.
5.
41 Wing bolt (C)
42 Trimmer guide
43 Templet guide
44 Screw
45 Templet guide
46 Lock plate lever
47 Bit
48 Base
49 Templet
50 Workpiece
51 Templet guide
52 Vaccum head
53 Screws
54 Support
55 Lock lever
56 Limit mark
57 Brush holder cap
58 Screwdriver

GENERAL SAFETY RULES

SAVE THESE INSTRUCTIONS.
Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3612C
12mm or 1/2''
0 – 60 mm
9,000 – 23,000
297 mm
160 mm
6.0 kg
GEA001-3