Installation And Connection; Radio Function - Trevi AVX 598USB Gebrauchs- Und Anschlusshandbuch

ENGLISH

INSTALLATION AND CONNECTION

Connect the satellite speaker cable jack (the one without controls) to the SPEAKER connector (6).
CONNECTING TO THE POWER SUPPLY
Fit the plug (10) into an AC 230V - 50Hz socket. Do not plug the appliance to different power.
Unless otherwise specified, the controls description applies to both the appliance and the remote control.
ON/OFF SWITCHING
1. Press the main ON/OFF switch (7).
2. Press the main ON/OFF switch again to switch the appliance off.
STANDBY
1. With the ON/OFF switch (7) set to ON, press the power-on/standby key (1) on the remote control to activate the appliance.
2. Press the power-on/standby key (1) again to switch the appliance back to standby mode.
CLOCK SETTING
1. Press the TIMESET key (24) to activate the clock setting. The first pair of digits (hour) on the time display (12) will start blinking.
2. Select the hour with keys (26) and (27) and then press the TIMESET(24) key. The second pair of digits (minutes) will start blinking.
3. Select the minutes with keys (26) and (27) and press the TIMESET(24) key again. The time will be stored and displayed.
VOLUME CONTROL AND MUTE FUNCTION
Volume can be adjusted with the remote control using the volume control keys (volume up 4) (volume down 5) on a scale from 0 to 30. During the
adjustment procedure the display will show the selected volume level.
MUTE function: it is possible to activate the audio off function with the MUTE key (2). To switch the audio on, press the MUTE key again.

RADIO FUNCTION

1. Switch the appliance on and press the input selection key (12) on the appliance or the INPUT key (28) on the remote control until the 'tuner' icon
(2) is displayed.
2. Press the SEARCH key (13) to automatically tune and store the radio stations. The appliance will automatically scan all the available radio stations
and will store up to a maximum of 20 stations; press the CH+ (21) or CH- (22) keys to recall the stored stations.
3. Adjust the volume as desired using keys (4) and (5).
4. To perform a manual search, use the (29) and (30) keys. Holding them will cause the appliance to tune on the first strong signal, pressing
them once will allow you to perform a step-by-step tuning, with frequency variations of 0.05 MHz.
The received radio station can be stored using the MEMORY key (23):
5. Press the MEMORY key (23). A number will start blinking on the display.
6. With the CH+ (21) and CH- (22) keys on the remote control, select the memory number that you want to use to store the station.
7. Press the MEMORY key (23) again.
NOTES
To obtain the best FM reception, extend and orient the antenna. If the reception is bad, try adjusting the length and orientation of the antenna. However,
the FM reception quality depends very much on where the appliance is placed.
USB/SD CARD PLAYER OPERATION
PLAYBACK
1. Insert an SD memory card in the SD slot (1) or a USB device in the USB port (2).
2. Switch the appliance on and press the input selection key (8) on the appliance or the INPUT key (28) on the remote control until the USB icon (3)
is displayed.
3. After a few seconds the player will automatically start playing the detected audio tracks (MP3).
4. Press the / key (18) to pause the playback.
5. To disable the pause press the / key (18) again.
6. If both an SD card and a USB device are present, the playback source can be changed using the USB/SD key (16), which enables switching from
SD card to USB device and vice versa.
TRACK SKIP
1. While listening, press the  key (20) to move to the next track; press the  key (19) to move to the previous track.
REPEAT PLAYBACK OF ALL TRACKS OR A SINGLE TRACK
The player plays all tracks available in the USB device/SD card in sequence and when it reaches the last track, it goes to the first one (continuous
repeat playback of all tracks).
By pressing key (15) on the remote control, the repeat function for a single track can be activated: the player will repeat the playback of the same
audio track. To return to standard playback and exit the single track repeat playback function, press key
7
AVX 598USB
(15) again.