Additional Information - Faber NIVA NV20AB Anleitung

4. Place the water tank in sink and remove cap, Anti-clockwise to open. (See Fig.5)
5. Fill tank with fi ltered tap water only. This is necessary to prolong the life of the fl ame and smoke producing unit.
The water should be fi ltered through a conventional domestic water fi lter unit and the fi lter should be replaced
regularly.
6. Screw the cap back on, do not overtighten.
7. Return the tank to the sump, with the tank cap facing down and the fl at side of the tank facing outward.
8. Gently place the fuelbed back into position.
9. Press Switch 'A' to 'ON' ( I ) position (See Fig.2)
Cleaning.
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.
We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-
Water Tank, Sump, Nozzle, Tank cap and seal, Air fi lter.
For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or
fl uff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan
heater.
Water tank
1. Remove water tank, as described earlier, put into sink and empty water.
2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in
the outer groove and the centre rubber seal.
3. Put a small quantity of washing up liquid into the tank, refi t the cap and shake well, rinse out until all traces of
washing up liquid are gone.
4. Refi ll with fi ltered tap water only, replace the cap, do not overtighten.
Sump
1. Press Switch 'A' to the 'OFF' (0) position
2. Gently lift out the fuelbed and place carefully on the ground. (See Fig.3)
3. Remove the water tank by lifting upwards.
4. Disconnect the electrical connector, located on the right side of the sump. (See Fig.6) .
5. Release the right sump locking tabs by turning 90º, this allows the sump to be lifted completely from its location.
(See Fig.6a)
6. Gently lift up the sump, taking care to keep level so as not to spill any water. Sit the assembly in the sink.
7. Release the left sump locking tabs by turning 90º, then lift off the Nozzle. (See Fig.4)
8. Lift out the transducer and carefully tilt, as shown, so that the liquid drains out of the sump. (See Fig.8)
9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces in the
sump and gently clean the transducer including the metal discs located in the top grooved surface. (See Fig.9)
10. When cleaned, thoroughly rinse the sump with clean water to remove all traces of washing up liquid.
11. Clean the outlet surface of the sump lid with the brush and fl ush out thoroughly with water. (See Fig.10)
12. Reverse the above steps to reassemble.
Air fi lter.
1. Press Switch 'A' to the 'OFF' (0) position (See Fig.2)
2. Gently lift out the fuelbed and place carefully on the ground. (See Fig.3)
3. Gently slide the air fi lter upwards out of its plastic holder. (See Fig.11)
4. Gently rinse with water in the sink and dry with fabric towel before returning.
5. Replace the fi lter making sure that the coarse black fi lter is facing the front of the fi re.
6. Replace the fuelbed.
7. Press Switch 'A' to the 'ON' ( I ) position (See Fig.2)

Additional Information

Recycling.
For electrical products sold within the European Community. At the end of the electrical products useful life it
should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
After Sales Service.
The product's warranty is valid for one year from the date of purchase. Within this period, we repair or replace this product
without any charge (with the exception of the light bulbs and depending on availability) and on the condition that the fi re has
been installed and used according to the aforementioned instructions. Your rights according to this warranty are an addition to
your legal rights, which are not affected by this warranty.
If you need service or want to purchase spare parts, please contact the shop in which you bought the fi re or call the service
telephone number of the country listed on the warranty. Keep your receipt as proof of purchase.
22