Call Reception; Intercom Call Management; Video Switching; Opening The Doors - urmet 1722 Installations- Und Gebrauchsanleitung

10.2. CALL RECEPTION

The following events will occur when the calling button is pressed:
• The camera LEDs will light up.
• The name tag backlighting will go off for a time.
• The video door phones will emit the call tone.
• The video stream of the calling station camera will appear on the "Master" video door phone. The green
will light up.
• The green button and the red
The video door phone will return to stand-by conditions if no button is pressed within three minutes from the call.
The following operations can be performed after a call on the "Master" video door phone:
• Press to turn the audio on: after having turned audio on, the button will turn green and conversation with the caller is possible for up to
3 minutes (the conversation can be interrupted at any time by pressing
While the audio is on, the name tag backlighting LEDs of the call station will be turned off.

10.3. INTERCOM CALL MANAGEMENT

To make an intercom call:
• Press button , which will start blinking green;
• Press or to send the call to the video door phone with which you want to establish a conversation (see the procedure for programming
the buttons under par. 7.4 PROGRAMMING THE INTERCOM FUNCTION);
• While waiting for a response, the LED of button
• When the video door phone called responds, the LED of button
• Press button to stop the conversation.

10.4. VIDEO SWITCHING

The call tone will be generated in alternating manner by the various video door phones after a call if "Slave" video door phones (OP3) are present
in the system. The "Master" video door phone will enable monitor switch-on if the call is from a video calling station. In this case, during the call
pick-up time (3 minutes from the call), the video door phones of the other devices can be switched on by pressing the auto-on button
switching function) until one of the video door phones picks up.
The picture of the main camera will appear only on the device that picked up afterwards.
The camera picture will therefore be normally shown on only one apartment station at a time.

10.5. OPENING THE DOORS

During a call, during communication (audio on) or during auto-on it is possible to:
• activate the pedestrian gate electric lock by pressing
• activate the garage gate lock by pressing .

10.6. AUTO POWER-ON

Press to see the video stream of the calling station camera on the video door phone.
Auto-on is silent (audio is not turned on) and the calling station LEDs will be off. During auto-on, the video stream of the camera will appear on
the video door phone monitor. The green
To exit the auto-on function, press
While the video door phone is displaying the images of the calling station, it is possible to:
• Turn the audio on to speak with the calling station by pressing B (the conversation can be interrupted at any time by pressing button
The camera LEDs will light up when audio is turned on.

10.7. CALL TONE MUTING

It is possible to adjust the call volume to the point of excluding the ring tone (Mute) by moving the sliding cursor (see section 10.1 DESCRIPTION
OF THE FRONT OF THE VIDEO DOOR PHONE).
The mute state is indicated by a red signal visible in the upper part of the cursor.
If the cursor is set to MUTE during a call, the video module of the video door phone will turn on, and all acoustic signals (beeps)
and any additional ringtones will be disabled.

10.8. SUPPLEMENTARY RINGER

The video door phones are provided with a pair of terminals (K, Z) for connecting a supplementary ringer. This ringer is controlled when any call
tone is generated.

10.9. VIDEO DOOR PHONE CALL TONE SELECTION

In systems with several video door phones, it may be useful to differentiate the call tone of the various devices.
• To access the call tone selection menu with the system in standby, press and hold
and the system will emit 3 confi rmation beeps to confi rm the new setting.
• Press ;
• The video door phones will emit the call tone.
• Press to vary the tone;
• To exit the programming mode, press and hold until you hear 3 confi rmation beeps and the Red programming LED stops fl ashing.
In all cases, the device will quit programming mode and save any changes after 10 minutes.
26
button will light up on the "Slave" video door phones.
is lit red;
;
button and the red
(in any case, after 3 minutes the device automatically switches off).
).
remains lit green for the entire time of the conversation;
button will light up.
for more than 5 seconds; the red LED will fl ash slowly
button and the red button
(video
).
DS1722-098A