Battery Warnings; Customer Service - Peg Perego RC BUGGY Gebrauch Und Wartung

BATTERY WARNINGS

Battery charging must be carried out and supervised
by adults only.
Do not allow children to play with the battery.
CHARGING THE BATTERY
• Charge the battery according to the instructions
enclosed with the battery charger and never for
more than 24 hours.
• To avoid damage, the battery should be charged as
soon as the vehicle starts to lose speed.
• If the vehicle is left unused for a long time,
remember to charge the battery and to keep it
disconnected from the electrical system. Repeat
the recharge procedure at least once every three
months.
• The battery must not be charged upside-down.
• Do not forget about the battery which is being
charged! Check it from time to time.
• Only use the battery charger provided and the
original PEG PEREGO battery.
• The battery is sealed and does not require
maintenance.
WARNING
• THE BATTERY CONTAINS CORROSIVE TOXIC
SUBSTANCES.
DO NOT TAMPER WITH IT.
• The battery contains acid-based electrolytes.
• Do not create direct contact between the battery
terminals, avoid strong impacts: risk of explosion
and/or fire.
• While charging, the battery produces gas. Charge
the battery in a well-ventilated environment, away
from sources of heat and flammable materials.
• The flat battery must be removed from the vehicle.
• It is not advisable to bring the battery into contact
with clothes, as it could damage them.
• Only use the recommended type of battery or an
equivalent type.
IF THERE IS A BATTERY LEAK
Protect your eyes. Avoid direct contact with the
electrolyte. Protect your hands.
Put the battery in a plastic bag and follow the
instructions for battery disposal.
IF SKIN OR EYES COME INTO CONTACT WITH
THE ELECTROLYTE
Thoroughly rinse the area concerned with running
water.
Consult a doctor immediately.
IF THE ELECTROLYTE IS SWALLOWED
Rinse the mouth and spit out the water.
Consult a doctor immediately.
MAINTENANCE AND VEHICLE CARE
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used. For repairs use only original PEG
PEREGO spare parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION!
The item is equipped with a brake system which
needs to be appropriately illustrated to the child by
an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted. See
the page on spare parts to find out how to identify the
serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Turn the vehicle upside down. In the front
section, insert the hole of the steering rod onto
the pin of the gear motor, as shown in the figure.
2 • Slightly lift the 2 steering levers, rotating them
until they engage with the ends of the steering
rod.
3 • Attach the 2 steering levers to the steering rod
with the respective screws and washers.
4 • Press to snap fit the hub caps onto the four
wheels.
5 • Insert the respective small bushes into the
housing inside the two wheels, as shown in the
figure.
6 • Insert a washer and a wheel onto each of the
two steering levers.
7 • Insert a self-locking washer into the special tool,
as shown in the figure. Important, the tabs on the
self-locking washer must be facing the inside of
the tool (see detail A).
NOTE: spare self locking washers are included in
the bag and these should be carefully conserved
in case one breaks and requires replacement.
8 • Holding the vehicle still, fix the wheel as shown
in the figure. Repeat for the other front wheel.
9 • Insert a self-locking washer into the special tool,
as shown in the figure. Important: the tabs of the
self locking washer must be facing the inside of
the tool (see detail A).
10 • Remove the grey protector caps from the ends
of the rear axle. Insert the axle into the tool, as
shown in the figure.
11 • Fully insert the 2 large bushes inside the wheels.
12 • Insert the axle into the wheel unit with the
hexagonal bushing already in place, as shown in
the figure.
13 • Insert the unit into the rear of the vehicle (gear
motor side), engaging the gear motor into the
bush as shown in the figure.
14 • Fully insert the large rounded bush inside the
remaining wheel.
15 • Insert a washer and the remaining wheel onto
the other end of the axle.
16 • Position the conical tool, which was used
previously, on the axle (gear motor side). Making
sure that the tool does not move, turn the
vehicle onto the gear motor side. Insert a self
locking washer into the remaining tool provided
and attach the wheel (see figure).
17 • Turn the vehicle back onto its wheels and fit the
four boss cover caps, making sure that the teeth
engage into the respective cavities.
18 • Fit the front mask, applying pressure to engage it
into its housing in the bodywork.
19 • Apply the transfers A and B.
20 • Press the front lights to snap them into place.
21 • Insert the windscreen into its three slots.
22 • Fasten the windscreen at the sides with the two
screws.
23 • Remove the protection cap from the steering
shaft and position the hole in the steering shaft
parallel to the windscreen. Connect the steering
wheel to the dashboard, as shown in the figure.
Insert the connected unit under the steering
wheel (see detail A).
24 • Insert the steering wheel onto the steering shaft,
taking care to insert the dashboard spring into
its cavity in the steering wheel.
25 • Fasten the steering wheel with the screw and nut
provided. IMPORTANT: the nut must be inserted
in the hexagonal hole and the screw in the round
hole.
26 • Connect the electrical system plug to the vehicle
battery.
27 • Position the seat support, engaging first the two
rear tabs (1) and then the two front tabs (2).
28 • Put the seat in the required position by inserting
the two front tabs and then engaging the rear tab
(detail A). Important: the seat can be set in three
different positions according to the height of the
child.
29 • Fasten the seat down with the screw.
30 • Insert the aerial unit with its spring in the hole in
the bodywork, as shown in the figure.
CONSUMER
IMPORTANT: check that the plate located in the
hole in the bodywork is visible and therefore
correctly inserted.
31 • Fasten it with the screw provided.
ASSEMBLY