Speed Correection; Job Menu; Saving Of A Job Program; Settings Menu - Cebora WF4-SS31 Bedienungsanleitung

7.1.17 "Speed Corr".
(only in MIG HD processes).
Allows the percentage correction of the wire speed as
compared to the preset speed.
Speed Correction
7.2 "JOB" MENU.
In this section you can save, modify, restore, copy or can-
cel the working programs.
From the " Main Menu ", with key T11, highlight the
"Jobs" item and enter the submenu by means of key T12.
7.2.1 Saving of a "JOB" program.
Once the adjustments and the settings described above
have been made, with keys T10 and T11 select a position
in the memory and press key T6 (SAVE) to save.
corresponding to keys T6, T7, T8 and T9:
- DEL: cancels the selected "Job".
- RCL: restores the selected "Job" to modify it.
- COPY: copies the selected "Job" and saves it in a dif-
ferent position.
7.3 MENU "Settings".
In this section you can set or modify the welding machine
main settings.
Via key T12 enter the submenu related to the selected
parameter.
7.3.1 Menu "Welding".
This submenu includes a list of welding parameters that
can be modifi ed:
- H2O MIG/TIG This function allows the setting of the
cooling unit start-up.
30
MIN MAX DEF.
-9.9% 9.9% 0.0%
The "Job" program
number, the welding pro-
cess and the wire diame-
ter are shown on the dis-
play.
When a "Job" has been
saved, the lower display
shows the abbreviations
From the "Main Menu"
(see par. 7), select menu
"Settings" via key T10
and display it with key
T11.
Here are listed all the pa-
rameters that the opera-
tor may modify:
- Welding
- Machine
- Factory Setup
- Languages
Range: ON-OFF-Auto (DEF OFF).
If "Auto" is selected, when the machine starts, the unit is run-
ning. If the torch trigger is not pressed after 30 seconds, it
shuts off. When the torch trigger is pressed, the unit starts
operating and shuts off 3 minutes after the torch trigger is
released.
- "Quality Control"
ON - OFF Setting (DEF OFF) (Available on demand).
- "Max inching"
The purpose is to stop the welding machine if the wire
fl ows for the preset length in cm after starting with no
passage of current.
OFF Setting - 50 cm (DEF OFF).
- "Push-Pull Force"
If the welding torch Push-Pull Art. 2008 is assembled,
the operations of the cooling unit and the PPF (Push
Pull Force) function are enabled. This function adjusts
the drive torque of the push-pull motor in order to
make the wire feed linear.
7.3.2 "Machine" Menu - " Machine Settings".
Here are available the following submenus:
- "Clock Setup" .
7.3.3 "Factory Setup" Menu - "Resetting of preset val-
ues ".
This item allows return to the factory preset values.
Three resetting modes are possible:
- All Complete resetting.
- Jobs only Resets only "Job" working programs
- Exclude jobs Resets all but saves "Job" working pro-
grams.
7.3.4 "Languages" Menu - "Language setup".
In this section you can select the language of the messag-
es displayed.

7.4 INFORMATION MENU.

Data concerning the power source software are displayed
in this section.

8 QUICK START-UP.

In the D3 display lower side, a few controls appear for the
quick access to the most common functions, related to
the various pages.
8.1 "MEM" - "SAVING" (see par. 7.2.1).
If you wish to save a welding program, press key T6, se-
lect keys T10 and T11, the "Job" number and then press
key T6 again to save the welding condition.
8.2 "PAR" - "PROCESS PARAMETERS" (see par. 7.1)
8.3 "2T/4T" - "TWO STAGES/ FOUR STAGES" (see par.
7.1.7).