Jacuzzi andros Montageanweisung, Bedienung Und Wartung Seite 28

The intensity of the whirlpool is determined by the amount of
air introduced into the water, regulated by means of control
knobs on the edge of the spa (
To obtain the maximum amount of air, turn each knob clock-
wise; turn counter-clockwise to reduce the amount of air.
Some of the hydromassage nozzles are connected to one
another via one or more diverters (
use the diverter to adjust the flow of water to a set of noz-
zles, with respect to the other set, in indirect proportion. That
is, by turning the knob one way or the other, the force of the
jets will increase in one set of nozzles and decrease in the
other.
CAUTION
Do not use the diverter(s) when the pump is in
action.
NOTE: some models have a white light led spotlight.
I
Press the "Light" key to turn on the spotlight (located on
the wall of the tub).
When turning on, the last programme used before the sub-
sequent turn off, will activate.
In the instance where you wish to select the subsequent
colour, colour cycle to the one displayed, press the key twice
within a couple of seconds:
- the first control turns off the spotlight.
- the second control activates the colour cycle following the one
just turned off.
To return to the initial display mode, scroll through all the
available options, repeatedly pressing the key.
The spotlight stays on for 2 hours. It can be shut off before
that by pressing the key again.
The colour combinations are regulated in terms of tones and
intensity by the built-in digital system.
Cromodream
This cycle allows you to experience the entire colour range -
colours appear in complimentary fashion, merging from one
colour to the next, providing complete satisfaction.
Sunlight
A colour trio (yellow/orange/white), with short interspersions
of sky blue and violet, reminiscent of the beneficial effects of so-
lar light; yellow alternated with violet uplifts mood and improves
general physical balance.
Relax
Formed of the following colours: blue/orange/sky blue/white;
this sequence relieves stress and encourages relaxation; the o-
range hue offers warmth in this sequence composed primarily
of "cold" colours.
i
8, detail A).
i
8, detail B). You can
Stable colours
You can also choose from the following colours, which appear
in stable fashion: white, light blue, orange, yellow, green.
I
Temperature control
The water is heated by a tubular electrical heater. Do not set
an excessively high water temperature, i.e. over the limit of 40
°C. The recommended temperature is 35-36 °C.
NOTE: If the electric consumption limiter is activated (se the
related chapter) should the pump be turned on at high speed,
the heater will be turned off (the symbol
display) and it is turned back on, if needed, 5 minutes after the
pump is turned off.
I
Temperature unit of measure
The temperature scale is set to °C (Celsius scale). It can be
changed to °F (Fahrenheit scale) as follows:
Press and hold the "Light"
til the message "cFn" appears.
If necessary, use the "Up"
scroll the menu until you see the message "cFn". Press the
"Light" key again to confirm the option.
Now insert the password 123 as follows:
- use the "Up" and/or "Down"
number.
- confirm the selection by pressing the "Light"
Perform the same steps to insert the other two numbers.
Once you have inserted the password, the display will show
the message I1x (where "x" may be 1 or 0; the memorized val-
ue is 0).
Use the keys "Up"
from 0 a 1 (corresponding to the scale in °F). Confirm the se-
lection with the "Light"
sage I2x.
Press the "Light"
and memorize the new values. The display will go off for a mo-
ment, and then it will come on again.
To go back to the Celsius scale (°C), return to the procedure and
set figure "x" of the parameter I1x to 0.
NOTE: If no key is pressed for 20 seconds, you will exit the
procedure and any changes made will not be saved.
I
Water heating temperature ("set point")
To check or modify the water heating temperature, do the follow-
ing:
28
will flash on the
key for about 12 seconds, un-
and/or "Down"
keys to insert the first
and/or "Down"
key. The display will show the mes-
key one more time to exit the procedure
keys to
key.
to change "x"