I
If you have not already done so,
cated on the power supply line of the tub.
I With your finger, touch (for at least half a second) any key on
the display: the screen will light up, showing the system is s-
tanding by to receive commands
NOTE: if you do not touch any key for 2 minutes, the screen
will go off. Touch any key again to re-activate it. Keep in mind
that if two keys are accidentally touched at the same time, y-
ou will need to wait about 3 seconds before you will be able
to activate another command.
i
I
(
)
Press key "D" to start the function. The key will light
3
up blue and the pump will start
NOTE: if the level of water in the tub is insufficient, the LED
will flash for about 2 seconds, and for about 30 seconds there
will be an acoustic signal to inform you that the function can-
not be activated. You must add water and press key "D" again.
I After 20 minutes the function will come to an end and the blue
light will go off. You can however stop the function any time
you like by pressing the key (D).
We suggest a hydromassage duration of about 15-20 minutes,
as it normally takes about 5 to 10 minutes for the revitalizing
and energizing effect of the moving water to take effect.
I We recommend you set the water temperature to 36 °C, even if
the duration of the hydromassage and the temperature of the
water are highly subjective factors, connected with the type of
treatment, physical conditions, or habits and preferences
At high water temperatures, we do however recommend de-
creasing the duration of the hydromassage, for example:
(°C)
34 - 36
36 - 38
38 - 40
Varying the intensity of the jets
I
If you want to vary the intensity of the jets, which is the
amount of air forced into the jets, press key "E" (
(variation takes place in a continuous manner).
ou have reached the desired effect, touch the key again to
stop the air adjustment. The air-water mix value will be applied
to subsequent hydromassage cycles, until you decide to
change it (again by means of the appropriate key).
Changing jets
You can customize the hydromassage even more, by chang-
ing the fixed and direction-adjustable nozzles (Hydro Jet) with
the rotating jets (Twist Jet), and vice versa.
The Hydro Jet nozzles allow you to experience an energetic,
localized jet, while the Twist Jets provide a lower intensity
massage over a greater area.
I Concerning the interchanging of the jets, refer to the chap-
ter "Assembly of Accessories" in this manual.
turn on the main switch lo-
(min)
20
15
10
i
)
3
When y-
Warnings
Soap or bubble bath (if not specifically intended for hy-
dromassage use) should be used only if you are not us-
ing the hydromassage.
Always remember to switch off the hydromassage before
emptying the tub.
I Attention: in models with a blower, after about 30 minutes
after the tub is emptied (when the sensor no longer detects
water in the tub) the blower is automatically activated for about
30 seconds. This is to force out any remaining water (which
got in while filling the tub) from the pipes connected to the noz-
zles on the bottom of the tub.
This also happens if the main switch is turned on without
having filled with water (i.e. if the tub is not filled within half
an hour, the blower is automatically activated after 30 sec-
onds).
You can activate this phase manually if you like, without hav-
ing to wait the 30 minutes previously mentioned:
- wait for the tub to drain completely.
- Touch key "A" with your finger. The blower will come on for
30 seconds, and then you can turn off the main switch locat-
ed on the power supply line of the tub.
I If you have been using the tub as a normal bathtub, in order
to expel residual water from the blower pipes, do the following:
- turn on the main switch located on the power supply line of
the tub;
i
(
1
- press key "A"
onds and the residual water in the pipes will be expelled.
- turn off the main switch.
I Attention: if the tub is cleaned a long time after emptying
it and without turning off the main switch, the level sensor may
detect water in the tub (holding a wet cloth over it for a few
seconds, or pointing the jet of water at the area where the sen-
sor is). Therefore, after 30 minutes, the blower will be auto-
matically activated for about 30 seconds in order to expel any
water which may be present in the pipes of the blower.
If the sensor does not detect the presence of water, or if
the tub is cleaned with the switch off, you can drain the tub
as described previously.
13
)
: the blower will come on for 30 sec-