Used Symbols; Fcc Compliance; Information On Intellectual Property; Functional Description And Specifications - Dremel 3D40 FLEX Bersetzung Der Original Bedienungsanleitung

USED SYMBOLS

Symbol Name
Warning symbol
WARNING
!
Read manual
symbol
V Volts
A Amperes
Hz
Hertz
Ø Diameter
o Off position
Alternating current
Hot surface
hazard symbol

FCC COMPLIANCE

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Changes and Modifications not expressly approved by
the manufacturer or registrant of this equipment can
void your authority to operate this equipment under
Federal Communications Commission's rules.
INFORMATION ON INTELLECTUAL
PROPERTY
The Dremel 3D40 FLEX is intended for 3D printing
objects from digital files that you create or own, or
have the right to print using the Dremel 3D40 FLEX.
When making objects using the Dremel 3D40 FLEX, it
is your responsibility to ensure that you do not infringe
any third party intellectual property rights or violate any
Designation/
applicable laws or regulations, such as U.S. or foreign
Explanation
intellectual property laws. The Dremel 3D40 FLEX may
not be used to make objects protected by intellectual
Alerts user to warning
property rights owned by third parties without such
messages
third parties' permission. Using the Dremel 3D40 FLEX
to do any of the following may require the permission
Alerts user to read
of third parties: to make a duplicate or facsimile (in
manual
whole or in part) of any object not created by you, to
make an object from a digital file you do not own, or to
Voltage
make an object from a scan of a physical object that
Current) you did not create. It is your responsibility to obtain
such permission. In some cases, you may not be able
Frequency, cycles per
to obtain such permission. Where such permission
second
cannot be obtained, you should not 3D print such
object, or you do so at your own risk. You may not
modify, reverse engineer, decompile, or disassemble
the Dremel 3D40 FLEX or its software or firmware,
Type or a characteristic
except as permitted by applicable law. If you use
of current
the Dremel 3D40 FLEX in any way other than as
recommended and described in these Operating/Safety
Contact may cause
Instructions, you do so at your own risk. Using the
burn. Allow to cool
Dremel 3D40 FLEX to make objects that infringe any
before servicing.
intellectual property rights owned by third parties could
result in civil or criminal prosecution and penalties,
The magnets of the
and you could be liable for money damages, fines, or
build plate holder
imprisonment.
generate a field that can
impair the
function of cardiac
pacemakers.
Extruder: Single extrusion
Extruder temperature: Up to 230°C (397°F)
Operating Interface: 3.5" full color IPS touch screen
Maximum Build Volume: 10" x 6" x 6.7" (255mm x
155mm x 170mm)
Layer Thickness: 50 microns | 0.5 mm
Filament Colors: See Dremel3D.com for color choices
Internal Storage: 4GB
External Storage: USB Flash Drive
Weight (without spool): 16kg (35lbs)
Dimensions: 20.25" x 16" x 15.9" (515mm x 406mm x
394mm)
ONLY works with Dremel 1.75mm filament
All polymers degrade with time. Do not unpack until
filament is needed. Filament should be stored at room
temperature: 16-29° C (60-85° F) and in dry conditions.
Dremel 3D40 FLEX comes with complimentary Dremel
Digilab 3D Slicing software for Windows and Mac
OSX. This application converts your 3D digital files into
buildable files.
371
FUNCTIONAL DESCRIPTION AND
SPECIFICATIONS
BUILDING
WEIGHT & DIMENSIONS
FILAMENT
FILAMENT STORAGE
SOFTWARE