Toshiba RAV-RM561BTP-E Anleitung Seite 71

Error codes and parts to be checked
Wired
Wireless remote controller
remote
Sensor block display of
controller
receiving unit
display
Main defective parts
Operation Timer
Ready
Indication Flashing
GR GR OR
No header remote
controller
E01
Remote controller
communication error
Remote controller
E02
transmission error
Indoor unit-remote
E03 controller regular
communication error
Indoor unit-outdoor
unit serial
communication error
E04
IPDU-CDB
communication error
Duplicated indoor
E08
addresses
Duplicated header
E09
remote controllers
CPU-CPU
E10
communication error
Header unit follower
E18 unit regular
communication error
IPDU communication
E31
error
Indoor unit heat
F01 ALT exchanger sensor
(TCJ) error
Indoor unit heat
F02 ALT exchanger sensor
(TC) error
Outdoor unit
F04 ALT discharge temp.
sensor (TD) error
Outdoor unit temp.
F06 ALT
sensor (TE / TS) error
F07 ALT TL sensor error
Outdoor unit outside
F08 ALT
air temp. sensor error
Indoor unit room
F10 ALT temp. sensor (TA)
error
F12 ALT TS sensor error
Heat sink sensor
F13 ALT
error
Temp. sensor
F15 ALT
connection error
Indoor unit, other P.C.
F29 SIM
board error
139-EN
Judging
Parts to be checked / error description
device
Incorrect remote controller setting --- The header
remote controller has not been set (including two
Remote
remote controllers).
controller
No signal can be received from the indoor unit.
System interconnection wires, indoor P.C. board,
Remote
remote controller
controller
--- No signal can be sent to the indoor unit.
Remote controller, network adapter, indoor P.C.
Indoor board --- No data is received from the remote
controller or network adapter.
System interconnection wires, indoor P.C. board,
Indoor outdoor P.C. board --- Serial communication error
between indoor unit and outdoor unit
Indoor address setting error --- The same address as
Indoor
the self-address was detected.
Remote controller address setting error --- Two
remote controllers are set as header in the double-
Remote
remote controller control.
controller
(* The header indoor unit stops raising alarm and
follower indoor units continue to operate.)
Indoor P.C. board --- Communication error between
Indoor
main MCU and motor microcomputer MCU
Indoor P.C. board --- Regular communication is not
Indoor possible between header and follower indoor units or
between twin header (main) and follower (sub) units.
Outdoor Communication error between IPDU and CDB
Heat exchanger sensor (TCJ), indoor P.C. board ---
Indoor Open-circuit or short-circuit of the heat exchanger
sensor (TCJ) was detected.
Heat exchanger sensor (TC), indoor P.C. board ---
Indoor Open-circuit or short-circuit of the heat exchanger
sensor (TC) was detected.
Outdoor temp. sensor (TD), outdoor P.C. board ---
Outdoor Open-circuit or short-circuit of the discharge temp.
sensor was detected.
Outdoor temp. sensors (TE / TS), outdoor P.C. board
Outdoor --- Open-circuit or short-circuit of the heat exchanger
temp. sensor was detected.
TL sensor may be displaced, disconnected or short-
Outdoor
circuited.
Outdoor temp. sensor (TO), outdoor P.C. board ---
Outdoor Open-circuit or short-circuit of the outdoor air temp.
sensor was detected.
Room temp. sensor (TA), indoor P.C. board --- Open-
Indoor circuit or short-circuit of the room temp. sensor (TA)
was detected.
TS sensor may be displaced, disconnected or short-
Outdoor
circuited.
Abnormal temperature was detected by the temp.
Outdoor
sensor of the IGBT heat sink.
Outdoor Temp. sensor (TE / TS) may be connected incorrectly.
Indoor Indoor P.C. board --- EEPROM error
Wired
Wireless remote controller
remote
Sensor block display of
controller
receiving unit
display
Operation Timer
Indication Ready Flashing
Air
GR GR OR
conditioner
status
F31 SIM
H01
*
H02
*
H03
Auto-
H04
reset
H06
Auto-
reset
L03 SIM
Auto-
L07 SIM
reset
L08 SIM
*
L09 SIM
L10 SIM
Auto-
reset
Auto-
L20 SIM
reset
Entire
stop
Auto-
L29 SIM
reset
Auto-
reset
L30 SIM
Entire
stop
L31 SIM
Entire
stop
P01 ALT
Entire
stop
P03 ALT
Operation
continued
P04 ALT
Auto-
reset
P05 ALT
Entire
stop
P07 ALT
Entire
stop
P10 ALT
Entire
stop
Auto-
reset
– 70 –
Judging
Main defective parts Parts to be checked / error description
device
Outdoor unit P.C. Outdoor P.C. board ---- In the case of EEPROM error. Entire
Outdoor
board
Current detect circuit, power voltage --- Minimum
Outdoor unit
frequency was reached in the current releasing
compressor Outdoor
control or short-circuit current (Idc) after direct
breakdown
excitation was detected
Outdoor unit Compressor circuit --- Compressor lock was detected. Entire
Outdoor
compressor lock
Current detect circuit, outdoor unit P.C. board ---
Outdoor unit current
Outdoor Abnormal current was detected in AC-CT or a phase
detect circuit error
loss was detected.
Case thermostat
Outdoor Malfunction of the case thermostat
operation
Current, high-pressure switch circuit, outdoor P.C.
Outdoor unit low-
Outdoor board --- Pressure sensor error was detected or low-
pressure system error
pressure protective operation was activated.
Duplicated header Indoor address setting error --- There are two or more
Indoor
indoor units header units in the group.
Group line in Indoor address setting error --- There is at least one
individual indoor unit Indoor group-connected indoor unit among individual indoor
units.
Indoor group address Indoor address setting error --- Indoor address group
Indoor
not set has not been set.
Indoor unit capacity
Indoor Indoor unit capacity has not been set.
not set
Outdoor unit P.C. In the case of outdoor P.C. board jumper wire (for
Outdoor
board service) setting error
Network
Address setting, central control remote controller,
LAN communication adapter
network adapter --- Duplication of address in central
error central
control communication
control
Other outdoor unit error
Other outdoor unit 1) Communication error between IPDU MCU and
Outdoor
error CDB MCU
2) Abnormal temperature was detected by the heat
sink temp. sensor in IGBT.
Abnormal external External devices, outdoor unit P.C. board ---
input into indoor unit Indoor Abnormal stop due to incorrect external input into
(interlock) CN80
Power supply phase sequence, outdoor unit P.C.
Phase sequence
Outdoor board --- Abnormal phase sequence of the 3-phase
error, etc.
power supply
Indoor fan motor, indoor P.C. board --- Indoor AC fan
Indoor unit fan error Indoor
error (fan motor thermal relay activated) was detected.
Outdoor unit An error was detected in the discharge temp.
discharge temp. error Outdoor
releasing control.
High-pressure switch --- The IOL was activated or an
Outdoor unit high-
pressure system error Outdoor error was detected in the high-pressure releasing
control using the TE.
The power wire may be connected incorrectly. Check
Open phase detected Outdoor
open phase and voltages of the power supply.
Abnormal temperature was detected by the temp.
Heat sink overheat Outdoor
sensor of the IGBT heat sink.
Drain pipe, clogging of drainage, float switch circuit,
Indoor unit water
Indoor indoor P.C. board --- Drainage is out of order or the
overflow detected
float switch was activated.
Air
conditioner
status
stop
Entire
stop
stop
Entire
stop
Entire
stop
Entire
stop
Entire
stop
Entire
stop
Entire
stop
Entire
stop
Entire
stop
Auto-
reset
Entire
stop
Entire
stop
Entire
stop
Operation
continued
(thermost
at OFF)
Entire
stop
Entire
stop
Entire
stop
Entire
stop
EN
Entire
stop
Entire
ID
stop
140-EN